Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- LOCTITE SI 5926 BL
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Silicone sealant
Manufacturers & Suppliers
Henkel Limited
manufacturer
2 Bishop Square Business Park, AL109EY Herfordshire Hatfield, Great Britain
+44 1606 593933
Emergency Contacts
Emergency Contact
+44 (0)1442 278497
24 Hours
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
Contains no dangerous substances exceeding the limits of the EU-Regulation
Acetic acid is liberated slowly upon contact with moisture.
Notes
Acetic acid is liberated slowly upon contact with moisture.
First Aid Measures
Emergency procedures for chemical exposure incidents
Move to fresh air. If symptoms persist, seek medical advice.
Rinse with running water and soap. Obtain medical attention if irritation persists.
Symptoms: Prolonged or repeated contact may cause skin irritation.
Rinse immediately with plenty of running water (for 10 minutes), seek medical attention from a specialist.
Symptoms: Prolonged or repeated contact may cause eye irritation.
Rinse mouth, drink 1-2 glasses of water, do not induce vomiting, consult a doctor.
Immediate Medical Attention
See section: Description of first aid measures
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Carbon dioxide, foam, powder, Fine water spray
None known
In the event of a fire, carbon monoxide (CO), carbon dioxide (CO2) and nitrogen oxides (NOx) can be released. carbon oxides.
In case of fire, keep containers cool with water spray.
Firefighter Protection
Wear self-contained breathing apparatus.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Avoid contact with skin and eyes. Ensure adequate ventilation.
Do not let product enter drains.
Scrape up as much material as possible.
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Use only in well-ventilated areas. Avoid skin and eye contact. See advice in chapter 8.
Store in a cool, well-ventilated place.
Wash hands before work breaks and after finishing work. Do not eat, drink or smoke while working. Good industrial hygiene practices should be observed.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Ensure good ventilation/extraction.
Chemical-resistant protective gloves (EN 374). Suitable materials for short-term contact or splashes (recommended: at least protection index 2, corresponding to > 30 minutes permeation time as per EN 374): nitrile rubber (NBR; >= 0.4 mm thickness) Suitable materials for longer, direct contact (recommended: protection index 6, corresponding to > 480 minutes permeation time as per EN 374): nitrile rubber (NBR; >= 0.4 mm thickness) This information is based on literature references and on information provided by glove manufacturers, or is derived by analogy with similar substances. Please note that in practice the working life of chemical-resistant protective gloves may be considerably shorter than the permeation time determined in accordance with EN 374 as a result of the many influencing factors (e.g. temperature). If signs of wear and tear are noticed then the gloves should be replaced.
Wear protective glasses.
Ensure adequate ventilation. An approved mask or respirator fitted with an organic vapour cartridge should be worn if the product is used in a poorly ventilated area Filter type: A
Wear suitable protective clothing.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Stable under recommended storage conditions.
Strong oxidizing agents. Polymerises in presence of water.
See section reactivity
No decomposition if used according to specifications.
See section reactivity
Acetic acid is liberated slowly upon contact with moisture. At higher temperatures (>150C) may release formaldehyde (traces).
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
Dispose of in accordance with local and national regulations.
Waste Codes
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for LOCTITE SI 5926 BL?
The signal word is no signal word.
What is the physical form of LOCTITE SI 5926 BL?
LOCTITE SI 5926 BL is a paste appearing as paste blue with blue color. It has acetic acid odor.
What is the solubility of LOCTITE SI 5926 BL?
Not available. (Solvent: Water); Partially soluble (Solvent: Acetone)
What is LOCTITE SI 5926 BL used for?
Silicone sealant
What is the melting point of LOCTITE SI 5926 BL?
The melting point is No data available / Not applicable and the boiling point is Not determined.