Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- Liquid Binder No.1
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Concrete/Mortar admixtures
Uses advised against
No further relevant information available.
Manufacturers & Suppliers
Refratechnik Steel GmbH
manufacturer
Schiess-Strasse 58, D-40549 Duesseldorf
+49 211 58 58 0
Emergency Contacts
Dpt. Research & Development
+49 211 58 58 171
during the regular office hours
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
Mixture of substances listed below with nonhazardous additions.
For the wording of the listed risk phrases refer to section 16.
Notes
Components with limit values at work place / dangerous components: Void
First Aid Measures
Emergency procedures for chemical exposure incidents
Supply fresh air; consult doctor in case of complaints.
Symptoms: Irritation to respiratory tract.
Immediately wash with water and soap and rinse thoroughly. In case of skin redness or inflammation take medical advice.
Symptoms: skin redness or inflammation
Rinse opened eye for several minutes under running water. Call a doctor immediately.
Rinse out mouth and then drink plenty of water. Do not induce vomiting, seek medical advice immediately and present this technical data sheet.
Immediate Medical Attention
Call a doctor immediately.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Use fire extinguishing methods suitable to surrounding conditions.
No further relevant information available.
Firefighter Protection
No special measures required.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Not required.
Dilute with plenty of water.
Send for recovery or disposal in suitable receptacles.
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Ensure good ventilation/exhaustion at the workplace.
Store in a closed and opaque container of non-corrodable material. Protect from frost.
No special measures required.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
The working place should be provided with an safety shower and eye-wash fountain.
Rubber gloves, PVC gloves. The glove material has to be impermeable and resistant to the product/ the substance/ the preparation. Selection of the glove material on consideration of the penetration times, rates of diffusion and the degradation. The exact break trough time has to be found out by the manufacturer of the protective gloves and has to be observed.
Face protection, Gauze goggles (EN 166)
Use suitable respiratory protective device in case of insufficient ventilation. Filter P2, Filter (EN 143).
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
No decomposition if used according to specifications.
No dangerous reactions known.
No further relevant information available.
Acids.
No dangerous decomposition products known.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
Disposal must be made according to official regulations.
Before elimination: Check whether the product has absorbed further substances during its use, and therefore has to be assigned to another waste group than initially recommended.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- Void
- Shipping Name
- Void
- Transport Class
- Void
- Packing Group
- Void
Regulatory Information
Chemical regulations, safety assessments, and compliance status
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for Liquid Binder No.1?
The signal word is no signal word.
What is the physical form of Liquid Binder No.1?
Liquid Binder No.1 is a liquid with white color. It has odourless odor.
What is Liquid Binder No.1 used for?
Concrete/Mortar admixtures
What is the melting point of Liquid Binder No.1?
The melting point is Undetermined. and the boiling point is 100 °C.