Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- LOCTITE SI 5300 RD
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Silicone adhesive
Manufacturers & Suppliers
Henkel Ltd
manufacturer
Wood Lane End, HP2 4RQ Hemel Hempstead, Great Britain
+44 1442 278000
Emergency Contacts
Emergency Contact
+44 (0)1442 278497
24 Hours
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS05
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Methyltriacetoxysilane EC: 224-221-9 | 4253-34-3 | 1 - 5% | Yes |
| octamethylcyclotetrasiloxane EC: 209-136-7 | 556-67-2 | 0.1 - 0.25% | Yes |
| Dodecamethylcyclohexasiloxane EC: 208-762-8 | 540-97-6 | 0.1 - 1% | Yes |
| Decamethylcyclopentasiloxane EC: 208-764-9 | 541-02-6 | 0.1 - 1% | Yes |
Notes
For full text of the H - statements and other abbreviations see section 16 "Other information". Substances without classification may have community workplace exposure limits available.
First Aid Measures
Emergency procedures for chemical exposure incidents
Move to fresh air. If symptoms persist, seek medical advice.
Rinse with running water and soap. Obtain medical attention if irritation persists.
Symptoms: Redness, inflammation.
Rinse immediately with plenty of running water (for 10 minutes), seek medical attention from a specialist.
Symptoms: Corrosive, may cause permanent damage to eyes (impairment of vision).
Rinse mouth, drink 1-2 glasses of water, do not induce vomiting, consult a doctor.
Immediate Medical Attention
See section: Description of first aid measures
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
water, carbon dioxide, foam, powder
High pressure waterjet
In the event of a fire, carbon monoxide (CO) and carbon dioxide (CO2) can be released. Silicon dioxide
In case of fire, keep containers cool with water spray.
Firefighter Protection
Wear self-contained breathing apparatus and full protective clothing, such as turn-out gear.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
wipe up with paper towel and place in container for disposal.
absorb onto inert absorbent material and place in sealed container for disposal.
Do not empty into drains / surface water / ground water.
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Avoid skin and eye contact. See advice in section 8
Ensure good ventilation/extraction. Keep container tightly sealed. Refer to Technical Data Sheet
Good industrial hygiene practices should be observed. Wash hands before work breaks and after finishing work. Do not eat, drink or smoke while working.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Ensure good ventilation/extraction.
Chemical-resistant protective gloves (EN 374). Suitable materials for short-term contact or splashes (recommended: at least protection index 2, corresponding to > 30 minutes permeation time as per EN 374): nitrile rubber (NBR; >= 0.4 mm thickness). Suitable materials for longer, direct contact (recommended: protection index 6, corresponding to > 480 minutes permeation time as per EN 374): nitrile rubber (NBR; >= 0.4 mm thickness). If signs of wear and tear are noticed then the gloves should be replaced.
Safety glasses with sideshields or chemical safety goggles should be worn if there is a risk of splashing. Protective eye equipment should conform to EN166.
Ensure adequate ventilation. An approved mask or respirator fitted with an organic vapour cartridge should be worn if the product is used in a poorly ventilated area. Filter type: A (EN 14387)
Wear suitable protective clothing. Protective clothing should conform to EN 14605 for liquid splashes or to EN 13982 for dusts.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Stable under recommended storage conditions.
Strong oxidizing agents. Polymerises in presence of water.
See section reactivity
Excessive heat.
See section reactivity.
Evolves acetic acid during cure.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
Do not empty into drains / surface water / ground water. Dispose of in accordance with local and national regulations.
Dispose of in accordance with local and national regulations.
Waste Codes
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for LOCTITE SI 5300 RD?
The signal word is danger.
What is the physical form of LOCTITE SI 5300 RD?
LOCTITE SI 5300 RD is a liquid appearing as liquid with red color. It has acetic acid odor.
What is the solubility of LOCTITE SI 5300 RD?
No data available / Not applicable
What is LOCTITE SI 5300 RD used for?
Silicone adhesive
What are the hazard statements for LOCTITE SI 5300 RD?
This substance has 3 hazard statements:
- H315: Causes skin irritation.
- H318: Causes serious eye damage.
- H412: Harmful to aquatic life with long lasting effects.
What is the melting point of LOCTITE SI 5300 RD?
The melting point is No data available / Not applicable and the boiling point is > 100 °C (> 212 °F).