Di-iso-propyl ether

Remove to fresh air. If not breathing, give artificial respiration. Get medical attention if symptoms occur.

Symptoms: Difficulty in breathing. Inhalation of high vapor concentrations may cause symptoms like headache, dizziness, tiredness, nausea and vomiting

Wash off immediately with plenty of water for at least 15 minutes. If skin irritation persists, call a physician.

Rinse immediately with plenty of water, also under the eyelids, for at least 15 minutes. Get medical attention.

Clean mouth with water and drink afterwards plenty of water.

CO₂, dry chemical, dry sand, alcohol-resistant foam. Water mist may be used to cool closed containers.

Do not use a solid water stream as it may scatter and spread fire.

Flammable. Risk of ignition. Vapors may form explosive mixtures with air. Vapors may travel to source of ignition and flash back. Containers may explode when heated. May form explosive peroxides. Thermal decomposition can lead to release of irritating gases and vapors. Keep product and empty container away from heat and sources of ignition.

Use personal protective equipment as required.

Should not be released into the environment. See Section 12 for additional Ecological Information.

Soak up with inert absorbent material. Keep in suitable, closed containers for disposal.

Materials: inert absorbent material

Wear personal protective equipment/face protection. Ensure adequate ventilation. Do not get in eyes, on skin, or on clothing. Avoid ingestion and inhalation. If peroxide formation is suspected, do not open or move container. Keep away from open flames, hot surfaces and sources of ignition. Use only non-sparking tools. To avoid ignition of vapors by static electricity discharge, all metal parts of the equipment must be grounded. Take precautionary measures against static discharges.

Keep containers tightly closed in a dry, cool and well-ventilated place.

Handle in accordance with good industrial hygiene and safety practice. Keep away from food, drink and animal feeding stuffs. Do not eat, drink or smoke when using this product. Remove and wash contaminated clothing and gloves, including the inside, before re-use. Wash hands before breaks and after work.

Keep away from open flames, hot surfaces and sources of ignition. Use only non-sparking tools.

Ensure adequate ventilation, especially in confined areas. Use explosion-proof electrical/ventilating/lighting equipment. Wherever possible, engineering control measures such as the isolation or enclosure of the process, the introduction of process or equipment changes to minimise release or contact, and the use of properly designed ventilation systems, should be adopted to control hazardous materials at source

Protective gloves. Glove material: Viton (R) - Breakthrough time: 480 minutes, Glove thickness: 0.4 mm, EU standard: EN 374 Level 6. Nitrile rubber - Breakthrough time: 480 minutes, Glove thickness: 0.35 mm, EU standard: EN 374 Level 6. PVC - Breakthrough time: 120 minutes, Glove thickness: 0.5 mm. As tested under EN374-3 Determination of Resistance to Permeation by Chemicals. Inspect gloves before use. Please observe the instructions regarding permeability and breakthrough time which are provided by the supplier of the gloves. (Refer to manufacturer/supplier for information) Ensure gloves are suitable for the task: Chemical compatability, Dexterity, Operational conditions, User susceptibility, e.g. sensitisation effects, also take into consideration the specific local conditions under which the product is used, such as the danger of cuts, abrasion. Remove gloves with care avoiding skin contamination.

Goggles (European standard - EN 166)

Follow the OSHA respirator regulations found in 29 CFR 1910.134 or European Standard EN 149. Use a NIOSH/MSHA or European Standard EN 149 approved respirator if exposure limits are exceeded or if irritation or other symptoms are experienced. Large scale/emergency use: Use a NIOSH/MSHA or European Standard EN 136 approved respirator if exposure limits are exceeded or if irritation or other symptoms are experienced. Recommended Filter type: low boiling organic solvent Type A conforming to EN 141. Small scale/Laboratory use: Maintain adequate ventilation No personal respiratory protective equipment normally required

Wear appropriate protective gloves and clothing to prevent skin exposure.

Prevent product from entering drains.

No special precautions required.

No special precautions required.