Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- CORROGLASS 602
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Coating Restricted to professional users.
Uses advised against
None known.
Manufacturers & Suppliers
Corrocoat Limited
manufacturer
Forster Street, Leeds, West Yorkshire, LS10 1PW, England
+44 (0)113 2760 760
Emergency Contacts
Emergency Contact
+44 (0)1652 641124
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS02
GHS07
GHS08
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| styrene EC: 202-851-5 | 100-42-5 | 15 - 25% | Yes |
| tris(2-methoxyethoxy)vinylsilane; 6-(2-methoxyethoxy)- 6-vinyl-2,5,7,10-tetraoxa-6-silaundecane EC: 213-934-0 | 1067-53-4 | 1% | Yes |
| Cobalt bis(2-ethylhexanoate) EC: 205-250-6 | 136-52-7 | 0.1% | Yes |
| N,N-dimethylaniline EC: 204-493-5 | 121-69-7 | 0.05% | Yes |
| 2-methoxyethanol EC: 203-713-7 | 109-86-4 | 0.01% | Yes |
Notes
According to REACH Regulation (EC) No 1907/2006, as retained and amended by SI 2019/758 and SI 2020/1577. See full text of H-phrases in section 16. Occupational exposure limits are listed in section 8, if these are available.
First Aid Measures
Emergency procedures for chemical exposure incidents
Bring the person into fresh air and stay with him/her.
Symptoms: breathing difficulties or irritation of the respiratory tract
Remove contaminated clothing and shoes immediately. Ensure to wash exposed skin thoroughly with water and soap. Skin cleanser can be used. DO NOT use solvents or thinners.
Symptoms: irritation
Flush eyes immediately with plenty of water or isotonic water (20-30 °C) for at least 5 minutes and continue until irritation stops. Remove contact lenses. Make sure to flush under upper and lower eyelids. Continue flushing during transport.
Symptoms: irritation
IF SWALLOWED: Immediately call a POISON CENTER/doctor. Do not induce vomiting! If vomiting occurs, keep head facing down so that vomit does not get into the lungs. Call a doctor or ambulance.
Symptoms: chemical pneumonia
Immediate Medical Attention
IF exposed or concerned: Get immediate medical advice/attention.
Medical Treatment
People who have swallowed the product should therefore be kept under medical attention for at least 48 hours.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Alcohol-resistant foam, carbon dioxide, powder, water mist.
Waterjets should not be used, since they can spread the fire.
Flammable liquid and vapour. In use may form flammable/explosive vapour-air mixture. Fire will result in dense smoke. Exposure to combustion products may harm your health.
Closed containers, which are exposed to fire, should be cooled with water.
Firefighter Protection
Wear self-contained breathing apparatus and protective clothing to prevent contact.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Storages not yet ignited must be cooled by water mist. Remove flammable materials if conditions allow it. Ensure sufficient ventilation. Avoid direct contact with spilled substances. Ensure adequate ventilation, especially in confined areas. Contaminated areas may be slippery.
Avoid discharge to lakes, streams, sewers, etc. In the event of leakage to the surroundings, contact local environmental authorities.
Contain and collect spillage. Wherever possible cleaning should be performed with normal cleaning agents. Avoid use of solvents.
Materials: non-combustible, absorbent material e.g. sand, earth, vermiculite or diatomaceous earth
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Ground and bond container and receiving equipment. Use explosion-proof [electrical/lighting/ventilating] equipment. Use non-sparking tools. Take action to prevent static discharges. Avoid direct contact with the product. Avoid contact during pregnancy and while nursing.
Store in tightly closed containers and store protected from moisture and light. Store locked up. Containers that have been opened must be carefully resealed and kept upright to prevent leakage. Must be stored in a cool and well-ventilated area, away from possible sources of ignition.
Smoking, drinking and consumption of food is not allowed in the work area.
Ground and bond container and receiving equipment. Use non-sparking tools. Take action to prevent static discharges. Store away from possible sources of ignition.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Do not recirculate outlet air that contain the substances. The formation of vapours must be kept at a minimum and below current limit values. Installation of a local exhaust system if normal air flow in the work room is not sufficient is recommended.
Material: Butyl, Glove thickness: 0,3 mm, Breakthrough time: >120 min, Standards: EN374-2, EN16523-1, EN388
Face shield, Safety glasses with side shields. Standards: EN166
Type: Combination Filter A1B1E1K1, Class: Class 1 (low capacity), Colour: Brown/Gray/Yellow/Green, Standards: EN14387
Dedicated work clothing should be worn.
Keep damming materials near the workplace. If possible, collect spillage during work.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
The product is stable under the conditions, noted in section 7 "Handling and storage".
Highly reactive and can auto-polymerize as a result of internal peroxide accumulation. The peroxides formed in these reactions are extremely shock- and heat-sensitive.
None known.
Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. Sunlight
Strong acids, strong bases, strong oxidizing agents, and strong reducing agents.
Under normal conditions of storage and use, hazardous decomposition products should not be produced.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
Dispose of contents/container to an approved waste disposal plant.
Dispose of contents/container to an approved waste disposal plant.
Waste Codes
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- UN1866
- Shipping Name
- RESIN SOLUTION
- Transport Class
- 3
- Packing Group
- III
See section 5.4.3, for instructions in writing regarding mitigation of damages in relation to incidents or accidents during transport.
Regulatory Information
Chemical regulations, safety assessments, and compliance status
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for CORROGLASS 602?
The signal word is danger.
What is the physical form of CORROGLASS 602?
CORROGLASS 602 is a liquid with no data available. color. It has aromatic, solvent odor.
What is CORROGLASS 602 used for?
Coating Restricted to professional users.
What are the hazard statements for CORROGLASS 602?
This substance has 6 hazard statements:
- H226: Flammable liquid and vapour.
- H304: May be fatal if swallowed and enters airways.
- H315: Causes skin irritation.
- H319: Causes serious eye irritation.
- H360FD: May damage fertility. May damage the unborn child.
- H412: Harmful to aquatic life with long lasting effects.
What is the melting point of CORROGLASS 602?
The melting point is No data available. and the boiling point is >100 °C.