Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- AESCULAP STERILIT POWER SYSTEMS OILSPRAY
- Product Code
- GB 600
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Preservative agent
Manufacturers & Suppliers
AESCULAP AG
manufacturer
Am AESCULAP-Platz, D-78532 Tuttlingen/Donau
++49 (0) 74 61 95-0
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
First Aid Measures
Emergency procedures for chemical exposure incidents
Move to fresh air in case of accidental inhalation of vapours. In the event of symptoms refer for medical treatment.
Wash off immediately with soap and plenty of water. Consult a doctor if skin irritation persists.
Rinse immediately with plenty of water, also under the eyelids, for at least 15 minutes. If eye irritation persists, consult a specialist.
Do not induce vomiting. Summon a doctor immediately. Induce vomiting only upon the advice of a physician.
Immediate Medical Attention
Summon a doctor immediately.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Foam, carbon dioxide (CO2), dry chemical, water-spray.
Full water jet
Fire may produce: Carbon monoxide and carbon dioxide. Heating will cause pressure rise with risk of bursting.
Cool containers at risk with water spray jet. Heating will cause pressure rise with risk of bursting.
Firefighter Protection
Use breathing apparatus with independent air supply.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Do not discharge into the drains/surface waters/groundwater. Do not discharge into the subsoil/soil.
Soak up with inert absorbent material (e.g. sand, silica gel, acid binder, universal binder). Shovel into suitable container for disposal.
Materials: inert absorbent material (e.g. sand, silica gel, acid binder, universal binder)
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Avoid contact with skin, eyes and clothing.
Keep containers tightly closed in a cool, well-ventilated place. Pressurized container: protect from sunlight and do not expose to temperatures exceeding 50 °C.
Do not spray on a naked flame or any incandescent material. Keep away from sources of ignition - No smoking.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Ensure adequate ventilation, especially in confined areas.
Splash protection: Protective gloves resistant to chemicals made off nitrile, Minimum coat thickness 0.4 mm, Permeation resistance (wear duration) approx. 120 minutes, i.e. protective glove <camatril 730 velours> made by www.kcl.de. This recommendation refers exclusively to the chemical compatibility and the lab test conforming to EN 374 carried out under lab conditions.
Safety goggles with side protection
In case of insufficient ventilation wear suitable respiratory equipment (gas filter type AX).
Long sleeved clothing.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Fire or intense heat may cause violent rupture of packages.
Strong oxidizing agents.
Carbon monoxide and carbon dioxide.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
Can be incinerated, when in compliance with local regulations.
Where possible recycling is preferred to disposal.
Waste Codes
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- 1950
- Shipping Name
- AEROSOLS
- Transport Class
- 2
Regulatory Information
Chemical regulations, safety assessments, and compliance status
Extremely flammable (F+). Harmful to aquatic organisms, may cause long-term adverse effects in the aquatic environment. Pressurized container. Observe employment restrictions for young people and child-bearing/nursing mothers.
Employment restrictions: Observe employment restrictions for young people. Observe employment restrictions for child bearing mothers and nursing. Special labelling: Pressurized container. Protect from sunlight and do not expose to temperatures exceeding 50 °C. Do not pierce or burn, even after use. Do not spray on a naked flame or any incandescent material. Keep away from sources of ignition - No smoking. Keep out of the reach of children.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for AESCULAP STERILIT POWER SYSTEMS OILSPRAY?
The signal word is na: r-phrases.
What is the physical form of AESCULAP STERILIT POWER SYSTEMS OILSPRAY?
AESCULAP STERILIT POWER SYSTEMS OILSPRAY is a aerosol with white color. It has hydrocarbon-like odor.
What is AESCULAP STERILIT POWER SYSTEMS OILSPRAY used for?
Preservative agent