Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- Potassium chloride solution 3 mol/l
- Product Code
- 1.04817
Regulatory Identifiers
- CAS Number
- N/A
- REACH No.
- This product is a mixture. REACH Registration Number see section 3.
Identified Uses
Reagent for analysis
Manufacturers & Suppliers
Merck Life Science UK Limited
manufacturer
New Road, The Old Brickyard, GILLINGHAM, Dorset, SP8 4XT, UNITED KINGDOM
+44 (0)1747 833-000
Emergency Contacts
CHEMTREC
+44 (0)870 8200418
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
GHS Pictograms
Still copying SDS data manually?Free
You don't have to. NextSDS reads this SDS and adds the information to your library automatically.
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
First Aid Measures
Emergency procedures for chemical exposure incidents
After inhalation: fresh air.
In case of skin contact: Take off immediately all contaminated clothing. Rinse skin with water/ shower.
After eye contact: rinse out with plenty of water. Remove contact lenses.
After swallowing: make victim drink water (two glasses at most). Consult doctor if feeling unwell.
Immediate Medical Attention
No data available
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Use extinguishing measures that are appropriate to local circumstances and the surrounding environment.
For this substance/mixture no limitations of extinguishing agents are given.
Not combustible. Fire may cause evolution of: Hydrogen chloride gas, Potassium oxides. Ambient fire may liberate hazardous vapours.
Suppress (knock down) gases/vapors/mists with a water spray jet.
Firefighter Protection
In the event of fire, wear self-contained breathing apparatus.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Do not breathe vapors, aerosols. Evacuate the danger area, observe emergency procedures, consult an expert.
Do not let product enter drains.
Take up with liquid-absorbent material (e.g. Chemizorb®). Clean up affected area.
Materials: liquid-absorbent material (e.g. Chemizorb®)
Related Products
Similar products with comparable safety profiles
Potassium chloride 3 mol/l
CAS: 7447-40-7
Potassium chloride 3 mol/l
CAS: 7447-40-7
Potassium chloride solution
---
Potassium chloride solution c(KCl) = 3 mol/L, 250 mL
---
Potassium chloride solution c(KCl) = 3 mol/L, 250 mL
---
Potassium Chloride 3 M
CAS: 7447-40-7
Potassium chloride 3 mol/l (3 N) in aqueous solution AVS TITRINORM® electrolytic solution
CAS: 7447-40-7
Potassium chloride
CAS: 7447-40-7
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
For precautions see section 2.2.
Tightly closed.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Full contact: Material: Nitrile rubber, Minimum layer thickness: 0.11 mm, Break through time: > 480 min, Material tested: KCL 741 Dermatril L. Splash contact: Material: Nitrile rubber, Minimum layer thickness: 0.11 mm, Break through time: > 480 min, Material tested: KCL 741 Dermatril L. Recommendation applies only to the product stated in the safety data sheet, supplied by us and for the designated use. When dissolving in or mixing with other substances and under conditions deviating from those stated in EN374 please contact the supplier of CE-approved gloves (e.g. KCL GmbH, D-36124 Eichenzell, Internet: www.kcl.de).
Use equipment for eye protection tested and approved under appropriate government standards such as NIOSH (US) or EN 166(EU). Safety glasses
Not required; except in case of aerosol formation.
Do not let product enter drains.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
The product is chemically stable under standard ambient conditions (room temperature).
No data available
Violent reactions possible with: The generally known reaction partners of water.
no information available
No data available
In the event of fire: see section 5
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
12.1 Toxicity
No data available
12.2 Persistence and degradability
12.3 Bioaccumulative potential
No data available
12.4 Mobility in soil
12.5 Results of PBT and vPvB assessment
The substance/mixture contains no components considered to be either persistent, bioaccumulative and toxic (PBT), or very persistent and very bioaccumulative (vPvB) at levels of 0.1% or higher.
12.6 Endocrine disrupting properties
The substance/mixture does not contain components considered to have endocrine disrupting properties at levels of 0.1% or higher.
12.7 Other adverse effects
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
Waste material must be disposed of in accordance with the national and local regulations.
Leave chemicals in original containers. No mixing with other waste.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
This material safety data sheet complies with the requirements of Regulation (EC) No. 1907/2006.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for Potassium chloride solution 3 mol/l?
The signal word is no signal word.
What is the physical form of Potassium chloride solution 3 mol/l?
Potassium chloride solution 3 mol/l is a liquid with colorless color. It has odorless odor.
What is Potassium chloride solution 3 mol/l used for?
Reagent for analysis
What is the melting point of Potassium chloride solution 3 mol/l?
The melting point is No data available and the boiling point is No data available.