Product Identification & Regulatory Data
Official chemical identifiers, CAS numbers, and regulatory compliance information
Basic Product Information
Regulatory Identifiers
Chemical Abstracts Service registry number - unique identifier for chemical substances
Uses Information
Overview
3-Hydroxyhexadecanoylcarnitine Inner Salt (Mixture of Diastereomers) is a off-white solid substance commonly used to be used only for scientific research and development..
Manage Your Safety Data Sheets
Organize and access your chemical safety data with ease.
GHS Hazard Classification & Safety Warnings
Globally Harmonized System (GHS) hazard pictograms, signal words, and safety classifications
Classification Status
Signal Word
GHS Hazard Pictograms & Safety Symbols
GHS (Globally Harmonized System) pictograms indicate specific chemical hazard categories and safety precautions
Hazard Statements
Precautionary Statements
Manufacturers & Suppliers
Authorized suppliers, manufacturers, and distribution network information
Toronto Research Chemicals
global supplier
2 Brisbane Road Toronto, ON M3J 2J8 CANADA
CA
+14166654439
24/7 Emergency Response
Critical emergency contact numbers for chemical spills, exposure incidents, and medical emergencies
Emergency Contact
+14166659696
CA
between 0800-1700 (GMT-5)
Chemical Composition & Hazardous Ingredients
Detailed component analysis, concentration ranges, and hazardous substance identification
Product Type
substanceChemical Components & Hazardous Substances
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| 3-Hydroxypalmitoylcarnitine | 195207-76-2 | Not specified | Non-hazardous |
Emergency First Aid Measures
Critical first aid procedures for chemical exposure incidents and medical emergencies
Inhalation Exposure
If inhaled, move casualty to fresh air. If not breathing, give artificial respiration and consult a physician.
Skin Contact
Wash affected area with soap and water. Consult a physician if any exposure symptoms are observed.
Eye Contact
Immediately rinse eyes with plenty of water for at least 15 minutes. Consult a physician.
Ingestion/Swallowing
Never give anything by mouth to an unconscious person. Rinse mouth with water. Do NOT induce vomiting unless advised to do so by a physician or Poison Control Center. Seek medical attention.
Related Chemical Substances & Alternative Products
Similar chemicals with comparable safety profiles and industrial applications
Technical Specifications & Material Properties
Physical state, chemical properties, melting point, boiling point, and material characteristics
Exposure Controls & Personal Protective Equipment
Occupational exposure limits, engineering controls, and required safety equipment
Engineering Controls
A laboratory fumehood or other appropriate form of local exhaust ventilation should be used to avoid exposure.
Hand Protection
Gloves should be used when handling this material. Gloves are to be inspected prior to use. Contaminated gloves are to be removed using proper glove removal technique so that the outer surface of the glove does not contact bare skin. Dispose of contaminated gloves after use in compliance with good laboratory practices and local requirements. Gloves used for incidental exposures (splash protection) should be designated as low chemical resistant or waterproof by EU standard EN 374. Unrated gloves are not recommended. Suggested gloves: AnsellPro nitrile gloves style 92-500 or 92-600, 5 mil thickness. Penetration time has not been determined. Gloves used for prolonged direct exposure (immersion) should be designated chemical resistant as per EN 734 with the resistance codes corresponding to the anticipated use of the material. Suggested gloves: AnsellPro Viton/Butyl gloves style 38-612, 4/8 mil thickness. Penetration time has not been determined. These recommendations may not apply if the material is mixed with any other chemical, or dissolved into a solution. A risk assessment must be performed to ensure the gloves will still offer acceptable protection.
Eye Protection
Safety glasses or safety goggles. All equipment should have been tested and approved under appropriate standards, such as NIOSH (US), CSA (Canada), or EN 166 (EU).
Respiratory Protection
Recommended respirators are NIOSH-approved N95 or CEN-approved FFP2 particulate respirators. These are to be only used as a backup to local exhaust ventilation or other engineering controls. If the respirator is the only means of protection, a full-face supplied air respirator must be used.
Skin/Body Protection
Fire resistant (Nomex) lab coat or coveralls.
Transportation & Shipping Information
UN numbers, shipping names, transport classes, and regulatory transport requirements
Chemical Safety FAQ & Common Questions
Most frequently asked questions about safety, handling, storage, and regulatory compliance
What is the hazard signal word for 3-Hydroxyhexadecanoylcarnitine Inner Salt (Mixture of Diastereomers)?
The signal word for this substance is "no signal word".
What is the physical form of 3-Hydroxyhexadecanoylcarnitine Inner Salt (Mixture of Diastereomers)?
3-Hydroxyhexadecanoylcarnitine Inner Salt (Mixture of Diastereomers) is a solid appearing as off-white solid with off-white color. It has no data available odor.
What is the solubility of 3-Hydroxyhexadecanoylcarnitine Inner Salt (Mixture of Diastereomers)?
DMSO, Methanol
What is 3-Hydroxyhexadecanoylcarnitine Inner Salt (Mixture of Diastereomers) used for?
To be used only for scientific research and development.
What is the melting point of 3-Hydroxyhexadecanoylcarnitine Inner Salt (Mixture of Diastereomers)?
The melting point is >97C (Subl.) and the boiling point is No data available.