Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- 2-Methylcitric Acid-d3 (Mixture of diastereomers)
- Product Code
- M265082
- Chemical Name
- 2-Methylcitric Acid-d3 (Mixture of diastereomers)
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
To be used only for scientific research and development.
Uses advised against
Not for use in humans or animals.
Manufacturers & Suppliers
Toronto Research Chemicals
manufacturer
2 Brisbane Road, Toronto, ON M3J 2J8, CANADA
+14166659696
Emergency Contacts
Emergency Contact
+1(416) 665-9696
between 0800-1700 (GMT-5)
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS07
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| 2-Hydroxy-1,2,3-butanetricarboxylic Acid-d3 | 146764-58-1 | --- | No |
First Aid Measures
Emergency procedures for chemical exposure incidents
If inhaled, move person to fresh air. If not breathing, give artificial respiration and consult a physician.
Wash affected area with soap and water. Consult a physician if any exposure symptoms are observed.
Immediately rinse eyes with plenty of water for at least 15 minutes. Consult a physician.
Never give anything by mouth to an unconscious person. Rinse mouth with water. Do NOT induce vomiting unless advised to do so by a physician or Poison Control Center. Seek medical attention.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Use water spray, alcohol-resistant foam, dry chemical or carbon dioxide.
Carbon oxides
Firefighter Protection
Wear self contained breathing apparatus for fire fighting if necessary.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Evacuate personnel to safe areas.
Prevent further leakage or spillage if safe to do so. Do not let product enter drains.
Pick up and arrange disposal without creating dust. Sweep up and shovel.
Materials: Keep in suitable, closed containers for disposal.
Related Products
Similar products with comparable safety profiles
2-Methylcitric Acid
---
Methylmalonyl DL-Carnitine-d3 Chloride (Mixture of Diastereomers)
---
Methylmalonyl DL-Carnitine Chloride (Mixture of Diastereomers)
CAS: 821794-54-1
3-Hydroxyhexadecanoylcarnitine Inner Salt (Mixture of Diastereomers)
---
4-Methyl-1,2-cyclohexanedicarboxylic anhydride, mixture of isomers
CAS: 19438-60-9
Di(propylene glycol) methyl ether acetate, mixture of isomers
CAS: 88917-22-0
Citric acid
CAS: 77-92-9
Citric acid monohydrate
CAS: 5949-29-1
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Avoid contact with skin and eyes. Avoid formation of dust and aerosols.
Keep container tightly closed in a dry and well-ventilated place. Keep in a dry place. Hygroscopic, -20°C Freezer, Under inert atmosphere
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
A laboratory fumehood or other appropriate form of local exhaust ventilation should be used to avoid exposure.
Gloves should be used when handling this material. Gloves are to be inspected prior to use. Contaminated gloves are to be removed using proper glove removal technique so that the outer surface of the glove does not contact bare skin. Dispose of contaminated gloves after use in compliance with good laboratory practices and local requirements. Gloves used for incidental exposures (splash protection) should be designated as “chemical resistant” by EU standard EN 374 with the resistance codes corresponding to the anticipated use of the material. Unrated gloves are not recommended. Suggested gloves: AnsellPro Sol-Vex nitrile gloves style 37-175, 15 mil thickness. Penetration time has not been determined. Gloves used for prolonged direct exposure (immersion) should be designated “chemical resistant” as per EN 734 with the resistance codes corresponding to the anticipated use of the material. Suggested gloves: AnsellPro Viton/Butyl gloves style 38-612, 4/8 mil thickness. Penetration time has not been determined.
Safety goggles or face shield. All equipment should have been tested and approved under appropriate standards, such as NIOSH (US), CSA (Canada), or EN 166 (EU).
Recommended respirators are NIOSH-approved N100 or CEN-approved FFP3 particulate respirators. These are to be only used as a backup to local exhaust ventilation or other engineering controls. If the respirator is the only means of protection, a full-face supplied air respirator must be used.
Fire resistant (Nomex) lab coat or coveralls.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Stable under recommended storage conditions.
No Data Available
No Data Available
No Data Available
Strong oxidizing agents
In the event of fire: See section 5. Other decomposition products: No data available.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
Product may be burned in an incinerator equipped with afterburner and scrubber. Excess and expired materials are to be offered to a licensed hazardous material disposal company.
Excess and expired materials are to be offered to a licensed hazardous material disposal company.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- Shipping Name
- Not dangerous goods
Regulatory Information
Chemical regulations, safety assessments, and compliance status
This safety data sheet complies with the requirements of WHMIS (Canada), OSHA 1910.1200 (US), and EU Regulation EC No. 1907/2006 (European Union).
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for 2-Methylcitric Acid-d3 (Mixture of diastereomers)?
The signal word is warning.
What is the physical form of 2-Methylcitric Acid-d3 (Mixture of diastereomers)?
2-Methylcitric Acid-d3 (Mixture of diastereomers) is a solid appearing as white to off-white solid with white to off-white color. It has odourless odor.
What is the solubility of 2-Methylcitric Acid-d3 (Mixture of diastereomers)?
DMSO (Slightly), Methanol (Slightly), Water (Slightly)
What is 2-Methylcitric Acid-d3 (Mixture of diastereomers) used for?
To be used only for scientific research and development.
What are the hazard statements for 2-Methylcitric Acid-d3 (Mixture of diastereomers)?
This substance has 1 hazard statement:
- H319: Causes serious eye irritation.
What is the melting point of 2-Methylcitric Acid-d3 (Mixture of diastereomers)?
The melting point is 140-145°C and the boiling point is No Data Available.