Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- Copper(II) sulfate anhydrous for analysis EMSURE
- Product Code
- 1.02791
- Chemical Name
- Copper(II) sulfate anhydrous
Regulatory Identifiers
- CAS Number
- 7758-98-7 Check regulations →
- EC Number
- 231-847-6 Check regulations →
Identified Uses
Reagent for analysis
Uses advised against
The product is being supplied under the TSCA R&D Exemption (40 CFR Section 720.36). It is the recipients responsibility to comply with the requirements of the R&D exemption. The product may not be used for a non-exempt commercial purpose under TSCA unless appropriate consent is granted in writing by MilliporeSigma.
Manufacturers & Suppliers
MilliporeSigma
manufacturer
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS07
GHS09
Hazard Statements
Precautionary Statements
Manage your Safety Data Sheets
Organize and access chemical safety data with ease
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Copper(II) sulfate anhydrous EC: 231-847-6 | 7758-98-7 | 100% | Yes |
First Aid Measures
Emergency procedures for chemical exposure incidents
After inhalation: fresh air.
In case of skin contact: Take off immediately all contaminated clothing. Rinse skin with water/ shower.
After eye contact: rinse out with plenty of water. Call in ophthalmologist. Remove contact lenses.
After swallowing: immediately make victim drink water (two glasses at most). Consult a physician.
Immediate Medical Attention
No data available
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
The data for this section has not been processed yet.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
The data for this section has not been processed yet.
Related Products
Similar products with comparable safety profiles
Copper sulfate-5-hydrate, fine crystals, for analysis
UFI: WHR2-HQ3P-2A7A-G2N7
Copper(II) sulfate
CAS: 7758-98-7
Copper(II) sulfate pentahydrate
CAS: 7758-99-8
Copper(II) sulfate pentahydrate
CAS: 7758-99-8
Copper(II) sulfate pentahydrate
CAS: 7758-99-8
Sulfuric acid 98% for analysis EMSURE
CAS: 7664-93-9
Aluminium potassium sulfate dodecahydrate for analysis EMSURE ACS,Reag. Ph Eur
CAS: 7784-24-9
Tin(II) chloride dihydrate for analysis (max. 0.000001% Hg) EMSURE
---
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
The data for this section has not been processed yet.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
This recommendation applies only to the product stated in the safety data sheet, supplied by us and for the designated use. When dissolving in or mixing with other substances and under conditions deviating from those stated in EN 16523-1 please contact the supplier of CE-approved gloves (e.g. KCL GmbH, D-36124 Eichenzell, Internet: www.kcl.de). Full contact Material: Nitrile rubber Minimum layer thickness: 0.11 mm Break through time: 480 min Material tested:KCL 741 Dermatril L This recommendation applies only to the product stated in the safety data sheet, supplied by us and for the designated use. When dissolving in or mixing with other substances and under conditions deviating from those stated in EN 16523-1 please contact the supplier of CE-approved gloves (e.g. KCL GmbH, D-36124 Eichenzell, Internet: www.kcl.de). Splash contact Material: Nitrile rubber Minimum layer thickness: 0.11 mm Break through time: 480 min Material tested:KCL 741 Dermatril L
Use equipment for eye protection tested and approved under appropriate government standards such as NIOSH (US) or EN 166(EU). Safety glasses
Recommended Filter type: Filter type P2 Millipore - 1.02791 The entrepeneur has to ensure that maintenance, cleaning and testing of respiratory protective devices are carried out according to the instructions of the producer. These measures have to be properly documented. required when dusts are generated. Our recommendations on filtering respiratory protection are based on the following standards: DIN EN 143, DIN 14387 and other accompanying standards relating to the used respiratory protection system.
protective clothing
Do not let product enter drains.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
The data for this section has not been processed yet.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- 3077
- Shipping Name
- Environmentally hazardous substance, solid, n.o.s. (CUPRIC SULFATE)
- Transport Class
- 9
- Packing Group
- III
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for Copper(II) sulfate anhydrous for analysis EMSURE?
The signal word is warning.
What is the physical form of Copper(II) sulfate anhydrous for analysis EMSURE?
Copper(II) sulfate anhydrous for analysis EMSURE is a solid appearing as form: solid color: light gray with light gray color. It has odorless odor.
What is Copper(II) sulfate anhydrous for analysis EMSURE used for?
Reagent for analysis
What are the hazard statements for Copper(II) sulfate anhydrous for analysis EMSURE?
This substance has 4 hazard statements:
- H302: Harmful if swallowed.
- H315: Causes skin irritation.
- H319: Causes serious eye irritation.
- H410: Very toxic to aquatic life with long lasting effects.
What is the melting point of Copper(II) sulfate anhydrous for analysis EMSURE?
The melting point is 200 C (392 F) and the boiling point is Not applicable.