Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- PLASITE 4301 HT PART B
- Product Code
- 4301H0000B
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Component of multicomponent industrial coatings - Industrial use.
Uses advised against
others than recommended
Manufacturers & Suppliers
StonCor Middle East L.L.C.
manufacturer
Plot # B518, Al Quoz Industrial Area 3, P.O. Box: 3034, Dubai, U.A.E.
+971 4 347 0460
Emergency Contacts
CHEMTREC
+1 703 5273887
Emergency Contact
112
24/7
Croatia
+3851 2348 342
24/7
HR, EN
Iceland
112
24/7
Malta
112
24/7
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS02
GHS05
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
Hazardous ingredients
First Aid Measures
Emergency procedures for chemical exposure incidents
Move to fresh air. Consult a physician after significant exposure.
Use a mild soap if available. Wash off immediately with soap and plenty of water while removing all contaminated clothes and shoes.
Rinse immediately with plenty of water, also under the eyelids, for at least 15 minutes. Remove contact lenses.
Gently wipe or rinse the inside of the mouth with water. Do NOT induce vomiting. Never give anything by mouth to an unconscious person.
Immediate Medical Attention
Immediate medical attention is required.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Carbon Dioxide, Dry Chemical, Foam
Alcohol, Alcohol based solutions, any other media not listed above.
No Information
In the event of fire, wear self-contained breathing apparatus.
Firefighter Protection
In the event of fire, wear self-contained breathing apparatus.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Ensure adequate ventilation. Use personal protective equipment.
Do not allow material to contaminate ground water system. Prevent product from entering drains.
soak up with non-combustible absorbent material, (e.g. sand, earth, diatomaceous earth, vermiculite) and transfer to a container for disposal according to local / national regulations
Materials: non-combustible absorbent material, (e.g. sand, earth, diatomaceous earth, vermiculite)
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Use only in area provided with appropriate exhaust ventilation. Wear personal protective equipment. Do not breathe vapours or spray mist.
Store in original container. Keep locked up or in an area accessible only to qualified or authorised persons. Store in a dry, well ventilated place away from sources of heat, ignition and direct sunlight.
Wash hands before breaks and at the end of workday. When using, do not eat, drink or smoke.
Store away from sources of heat and ignition.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Ensure adequate ventilation, especially in confined areas.
Impervious gloves.
Tightly fitting safety goggles.
Respirator with filter for organic vapor.
Long sleeved clothing. Remove and wash contaminated clothing before re-use.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Stable under normal conditions.
No reactivity hazards known under normal storage and use conditions.
Hazardous polymerisation may occur.
Direct sources of heat.
Strong oxidizing agents.
Carbon dioxide (CO2), carbon monoxide (CO), oxides of nitrogen (NOx), dense black smoke.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
If recycling is not practicable, dispose of in compliance with local regulations.
If recycling is not practicable, dispose of in compliance with local regulations.
Waste Codes
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- UN 3105
- Shipping Name
- Organic Peroxide, Liquid
- Transport Class
- 5.2
- Packing Group
- II
Regulatory Information
Chemical regulations, safety assessments, and compliance status
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for PLASITE 4301 HT PART B?
The signal word is danger.
What is the physical form of PLASITE 4301 HT PART B?
PLASITE 4301 HT PART B is a liquid appearing as colorless to light yellow liquid with colorless to light yellow liquid color. It has irritating odor.
What is PLASITE 4301 HT PART B used for?
Component of multicomponent industrial coatings - Industrial use.
What are the hazard statements for PLASITE 4301 HT PART B?
This substance has 2 hazard statements:
- H242: Heating may cause a fire.
- H314: Causes severe skin burns and eye damage.
What is the melting point of PLASITE 4301 HT PART B?
The melting point is Not determined and the boiling point is 68 - N.D. °C.