NextSDS Logo
Safety Data Sheet EN

ALUXAL 108 SA 25 KG

How compliant is your chemical safety?

Free 2-minute compliance assessment

Check Now
01

Identification

Product identifiers, regulatory numbers, and supplier information

Product Information

Product Name
ALUXAL 108 SA 25 KG
Product Code
ALUX108SA25

Regulatory Identifiers

CAS Number
N/A

Identified Uses

Covering and scorifying flux for Aluminium alloys.

Manufacturers & Suppliers

A

A.CESANA S.R.L.

undefined

Via F. Turati, 23 20016 PERO (MI) ITALIA

Emergency Contacts

Emergency Contact

+39 02-3534941

02

Hazard Identification

GHS classification, signal word, pictograms, and hazard statements

Classified no signal word

Hazard Classifications

GHS Pictograms

Manage your Safety Data Sheets

Organize and access chemical safety data with ease

Manage SDS
03

Composition / Information on Ingredients

Chemical components, concentration ranges, and hazardous substance identification

Type mixture
Chemical Name CAS Number Concentration Hazardous
SODIUM FLUOSILICATE EC: 240-934-8 16893-85-9 5 - 15% Yes
SODIUM CARBONATE EC: 207-838-8 497-19-8 5 - 15% Yes

Notes

The full wording of the Risk (R) and hazard (H) phrases is given in section 16 of the sheet.

04

First Aid Measures

Emergency procedures for chemical exposure incidents

Inhalation

Remove to open air. If breathing is irregular, seek medical advice.

Skin contact

Wash immediately with plenty of water. Remove contaminated clothing. Wash contaminated clothing before using them again.

Symptoms: Irritation

Eye contact

Irrigate copiously with clean, fresh water for at least 15 minutes. Seek medical advice.

Ingestion

Obtain immediate medical attention. Induce vomiting only if indicated by the doctor. Never give anything by mouth to an unconscious person.

Immediate Medical Attention

Seek medical advice (for eyes and irregular breathing). If irritation persists, seek medical attention (for skin). Obtain immediate medical attention (for ingestion).

Medical Treatment

Follow doctor's orders.

Related Substances

Similar chemicals with comparable safety profiles

08

Exposure Controls / PPE

Occupational exposure limits, engineering controls, and protective equipment

Engineering

As the use of adequate technical equipment must always take priority over personal protection equipment, make sure that the workplace is well aired through effective local aspiration or bad air vent. If such operations do not make it possible to keep the concentration of the product below the permitted workplace exposure thresholds a suitable respiratory tract protection must be used.

Hands

Protect hands with category II (ref. Directive 89/686/EEC and standard EN 374) work gloves, such as those in PVC, neoprene, nitryl or equivalent. The following should be considered when choosing work glove material: degradation, breakage times and permeation. Work glove resistance to preparations should be checked before use, as it can be unpredictable. Gloves’ limit depends on the duration of exposure.

Eyes

Wear protective airtight goggles (ref. standard EN 166). In the presence of risks of exposure to splashes or squirts during work, adequate mouth, nose and eye protection should be used to prevent accidental absorption.

Respiratory

If the threshold value for one or more of the substances present in the preparation for daily exposure in the workplace or to a fraction established by the company’s prevention and protection service is exceeded, wear an FFP3 (ref. standard EN 141) type half mask. The use of breathing protection equipment, such as masks with organic vapour and dust/mist cartridges, is necessary in the absence of technical measures limiting worker exposure. The protection provided by masks is in any case limited. If the substance in question is odourless or its olfactory threshold is higher than the relative exposure limit and in the event of an emergency, or when exposure levels are unknown or the concentration of oxygen in the workplace is less than 17% volume, wear self-contained, open-circuit compressed air breathing apparatus (ref. standard EN 137) or fresh air hose breathing apparatus for use with full face mask, half mask or mouthpiece (ref. standard EN 138).

Skin/Body

Wear category II professional long-sleeved overalls and safety footwear (ref. Directive 89/686/CEE and standard EN 344).

09

Physical and Chemical Properties

Appearance, physical state, melting point, boiling point, and material characteristics

Physical State
powder
Physical State Data
solid
State Under Standard Conditions
---
Appearance
powder
Colour
white
Colour Intensity
---
Form
powder
Odor
no odour
Odor Threshold
Not available.
Ph
basico
Melting Point
Not available.
Boiling Point
Not available.
Flash Point
Not available.
Freezing Point
Not available.
Softening Point
---
Solidification Point
---
Cloud Point
---
Crystallisation Point
---
Relative Evaporation Rate
---
Evaporation Rate
Not available.
Vapor Pressure
Not available.
Vapor Density
Not available.
Relative Density
---
Bulk Density
---
Density
1,200 g/cm3
Flammability
Not available.
Upper Explosive Limit
Not available.
Lower Explosive Limit
Not available.
Explosive Limits
---
Auto Ignition Temperature
Not available.
Decomposition Temperature
Not available.
Solubility
---
Partition Coefficient
Not available.
Solubility In Water
partially soluble in water
Solubility In Fat
---
Molecular Weight
---
Voc Content
0
Metal Corrosion
---
Dynamic Viscosity
---
Kinematic Viscosity
---
Properties Status
---
14

Transport Information

UN numbers, shipping names, transport classes, and regulatory requirements

?

Frequently Asked Questions

Common questions about safety, handling, and properties

What is the hazard signal word for ALUXAL 108 SA 25 KG?

The signal word is no signal word.

What is the physical form of ALUXAL 108 SA 25 KG?

ALUXAL 108 SA 25 KG is a powder appearing as powder with white color. It has no odour odor.

What is ALUXAL 108 SA 25 KG used for?

Covering and scorifying flux for Aluminium alloys.

What is the melting point of ALUXAL 108 SA 25 KG?

The melting point is Not available. and the boiling point is Not available..

Compliance Scan

Free compliance check