Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- Wolsit SP
Regulatory Identifiers
- CAS Number
- N/A
- UFI Code
- V3KS-CMXN-9U1C-QH7Y
Identified Uses
Waterbased additive for liquid processing systems
Uses advised against
Reserved for industrial use.
Manufacturers & Suppliers
Wolman Wood and Fire Protection GmbH
manufacturer
Dr.-Wolman-Strasse 31-33, 76547 Sinzheim
+4972218000
Emergency Contacts
GBK GmbH Global Regulatory Compliance
+49(0)6132-84463
24-Hour-Number
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS05
GHS07
GHS09
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
Preparation based on: 5-chloro-2-methyl-2H-isothiazol-3-one 2-methyl-2H-isothiazol-3-one
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| mixture of: 5-chloro-2-methyl-4-isothiazolin-3-one and 2-methyl-4-isothiazolin-3-one (3:1) | 55965-84-9 | 1 - 2.5% | Yes |
| copper dinitrate EC: 221-838-5 | 3251-23-8 | 1% | Yes |
First Aid Measures
Emergency procedures for chemical exposure incidents
If difficulties occur after vapour/aerosol has been inhaled, remove to fresh air and seek medical attention.
After contact with skin, wash immediately with plenty of water and soap. Under no circumstances should organic solvent be used. If irritation develops, seek medical attention.
Wash affected eyes for at least 15 minutes under running water with eyelids held open, consult an eye specialist.
Immediately rinse mouth and then drink 200-300 ml of water, seek medical attention. Do not induce vomiting unless told to by a poison control center or doctor.
Medical Treatment
Treat according to symptoms (decontamination, vital functions)
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Foam, Water spray, Dry powder, Carbon dioxide (CO2)
water jet
Firefighter Protection
Wear a self-contained breathing apparatus.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Do not breathe vapour/aerosol/spray mists. Handle in accordance with good industrial hygiene and safety practice.
Large spills should be collected mechanically (remove by pumping) for disposal.
Contain contaminated water/firefighting water.
Pick up with suitable absorbent material (e.g. sand, sawdust, general-purpose binder, kieselguhr).
Materials: sand, sawdust, general-purpose binder, kieselguhr
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Avoid contact with the skin, eyes and clothing. Smoking, eating and drinking are forbidden in application area. For personal protection see section 8. Comply with the health and safety at work laws.
Keep away from food, drink and animal feedingstuffs. Keep only in the original container. Keep container tightly closed. Store protected against freezing. Keep locked-up and out of reach of children. Storage temperature min 5 °C
When using, do not eat, drink or smoke. Hands and/or face should be washed before breaks and at the end of the shift. At the end of the shift the skin should be cleaned and skin-care agents applied. Gloves must be inspected regularly and prior to each use. Replace if necessary (e.g. pinhole leaks).
No special precautions necessary.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Suitable chemical resistant safety gloves (EN 374) also with prolonged, direct contact (Recommended: Protective index 6, corresponding > 480 minutes of permeation time according to EN 374): E.g. nitrile rubber (0.4 mm), chloroprene rubber (0.5 mm), butyl rubber (0.7 mm) etc. Manufacturer's directions for use should be observed because of great diversity of types.
Tightly fitting safety goggles (splash goggles) (e.g. EN 166)
Wear respiratory protection if ventilation is inadequate. Combination filter for gases/vapours of organic, inorganic, acid inorganic and alkaline compounds (e.g. EN 14387 Type ABEK).
Body protection must be chosen based on level of activity and exposure.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
The product is stable if stored and handled as prescribed/indicated.
No hazardous reactions if stored and handled as prescribed/indicated.
The product is stable if stored and handled as prescribed/indicated.
See SDS section 7 - Handling and storage.
Strong oxidizing agents, Strong reducing agents
No hazardous decomposition products if stored and handled as prescribed/indicated.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
This material and its container must be disposed of in a safe way. Must be sent to a suitable incineration plant, observing local regulations.
Must be sent to a suitable incineration plant, observing local regulations.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- 3265
- Shipping Name
- CORROSIVE LIQUID, ACIDIC, ORGANIC, N.O.S. (5-CHLORO-2-METHYL-2H-ISOTHIAZOL-3-ONE)
- Transport Class
- 8
- Packing Group
- II
Regulatory Information
Chemical regulations, safety assessments, and compliance status
Biocidal Products Regulation 528/2012/EU. To avoid risks to man and the environment, comply with the instructions for use. Take note of Directive 94/33/EC on the protection of young people at work or stricter national regulations, where applicable.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for Wolsit SP?
The signal word is danger.
What is the physical form of Wolsit SP?
Wolsit SP is a liquid with green color. It has mild odor.
What is Wolsit SP used for?
Waterbased additive for liquid processing systems
What are the hazard statements for Wolsit SP?
This substance has 3 hazard statements:
- H314: Causes severe skin burns and eye damage.
- H317: May cause an allergic skin reaction.
- H410: Very toxic to aquatic life with long lasting effects.
What is the melting point of Wolsit SP?
The melting point is -3 °C and the boiling point is 100 °C.