Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- edding permanent ink (blue) contained in: edding 300, edding 330
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Refilling ink
Uses advised against
No data available.
Manufacturers & Suppliers
edding International GmbH
manufacturer
Bookkoppel 7, D-22926 Ahrensburg
+49 (0) 41 02 / 80 8-0
Emergency Contacts
Giftnotruf Berlin
+49 (0)30 30686 790
DE, EN
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS02
GHS07
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
First Aid Measures
Emergency procedures for chemical exposure incidents
Remove affected person from the immediate area. Ensure supply of fresh air.
Wash off immediately with soap and water. Do NOT use solvents or thinners.
Remove contact lenses. Rinse eye thoroughly under running water keeping eyelids wide open and protecting the unaffected eye (at least 10 to 15 minutes). Seek medical assistance.
Rinse mouth thoroughly with water. Call a doctor immediately. Never give anything by mouth to an unconscious person.
Immediate Medical Attention
Seek medical assistance (for eye contact). Call a doctor immediately (for ingestion).
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Alcohol-resistant foam; Extinguishing powder; Carbon dioxide; Water spray jet
High power water jet
In the event of fire, the following can be released: Carbon dioxide (CO2); Carbon monoxide (CO)
Cool endangered containers with water spray jet. Suppress gases/vapours/mists with water spray jet.
Firefighter Protection
Use self-contained breathing apparatus. Wear protective clothing.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Refer to protective measures listed in sections 7 and 8. Avoid contact with skin, eyes and clothing. Ensure adequate ventilation. Keep away sources of ignition.
Do not discharge into the drains/surface waters/groundwater. Do not discharge into the subsoil/soil.
Take up with absorbent material. Send in suitable containers for recovery or disposal.
Materials: sand, kieselguhr, universal binder
Related Products
Similar products with comparable safety profiles
edding permanent ink (red) contained in: edding 300, edding 330
---
edding permanent ink (black) contained in: edding 400
---
edding Permanent Marker Refill Ink T25, T100, T1000 (blue) contained in: edding 800
---
edding Permanent Marker Refill Ink T25, T100, T1000, MTK25 (blue) contained in: edding 3000
---
edding Permanent Marker Refill Ink T25, T100, T1000, MTK25 (blue) contained in: edding 400
---
edding Permanent Marker Refill Ink T25, T100, T1000, MTK25 (red) contained in: edding 3000
---
edding Permanent Marker Refill Ink T25, T100, T1000, MTK25 (green) contained in: edding 3000
---
edding Permanent Marker Refill Ink T25, T100, T1000, MTK25 (black) contained in: edding 3000
---
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Provide good ventilation at the work area (local exhaust ventilation, if necessary). Product inherent handling risks must be minimised taking the appropriate measures for protection and preventive actions. The working process should be designed to rule out the release of hazardous substances or skin contact as far it is possible by the state of the art.
Keep container tightly closed and dry in a cool, well-ventilated place. Protect from heat and direct sunlight.
Do not eat, drink or smoke during work time. Keep away from foodstuffs and beverages. Avoid contact with eyes and skin. Remove soiled or soaked clothing immediately. Do not inhale vapours. Clean skin thoroughly after work; apply skin cream.
Vapours can form an explosive mixture with air. Take precautionary measures against static charges. Keep away from sources of heat and ignition.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
No data available.
Sufficient protection is given wearing suitable protective gloves checked according to i.e. EN 374, in the event of risk of skin contact with the product. Before use, the protective gloves should be tested in any case for its specific workstation suitability (i.e. mechanical resistance, product compatibility and antistatic properties). Adhere to the manufacturer's instructions and information relating to the use, storage, care and replacement of protective gloves. Protective gloves shall be replaced immediately when physically damaged or worn. Design operations thus to avoid permanent use of protective gloves. Appropriate Material butyl rubber. Material thickness 0.5 mm. Breakthrough time > 240 min.
Safety glasses with side protection shield (EN 166)
If workplace exposure limits are exceeded, a respiration protection approved for this particular job must be worn. In case of aerosol and mist formation, take appropriate measures for breathing protection in the event workplace threshold values are not specified.
Normal chemical work clothing.
No data available.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Stable under recommended storage and handling conditions (See section 7).
No data available.
No data available.
No data available.
Acids; Alkalis; Oxidizing agents
Hydrogen
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- UN1263
- Shipping Name
- PAINT RELATED MATERIAL
- Transport Class
- 3
- Packing Group
- II
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for edding permanent ink (blue) contained in: edding 300, edding 330?
The signal word is danger.
What is the physical form of edding permanent ink (blue) contained in: edding 300, edding 330?
edding permanent ink (blue) contained in: edding 300, edding 330 is a liquid with blue color. It has characteristic odor.
What is edding permanent ink (blue) contained in: edding 300, edding 330 used for?
Refilling ink
What are the hazard statements for edding permanent ink (blue) contained in: edding 300, edding 330?
This substance has 2 hazard statements:
- H225: Highly flammable liquid and vapour.
- H336: May cause drowsiness or dizziness.
What is the melting point of edding permanent ink (blue) contained in: edding 300, edding 330?
The melting point is No data available and the boiling point is > 70 °C.