Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- MICROLUBE GL 261
- Product Code
- 020195
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Lubricant.
Uses advised against
Consumer use
Manufacturers & Suppliers
Küber Lubrication NA, LP
32 Industrial Drive, Londonderry, NH 03053
(603) 647-4104
Emergency Contacts
CHEMTREC
1-800-424-9300
INTERNATIONAL
(703) 527-3887
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
GHS Pictograms
Hazard Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
The product contains no substances which at their given concentration, are considered to be hazardous to health.
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Mineral oil | --- | 50 - 60% | No |
First Aid Measures
Emergency procedures for chemical exposure incidents
Move to fresh air in case of accidental inhalation of fumes from overheating or combustion. If symptoms persist, call a physician.
Rinse with plenty of water. If skin irritation persists, call a physician.
Flush eye with water for 15 minutes. If symptoms persist, call a physician.
Do not induce vomiting. Consult a physician.
Immediate Medical Attention
If symptoms persist, call a physician.
Medical Treatment
Treat symptomatically.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Carbon dioxide (CO2). Dry chemical. Dry sand. Water spray mist or foam.
Do not use a solid water stream as it may scatter and spread fire
Thermal decomposition can lead to release of irritating gases and vapors. Water may be used to cool closed containers.
Standard procedure for chemical fires.
Firefighter Protection
In the event of fire and/or explosion do not breathe fumes. In the event of fire, wear self-contained breathing apparatus.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Avoid contact with skin, eyes and clothing.
Do not allow material to contaminate ground water system. Prevent product from entering drains.
Scrape-up. Pick up and transfer to properly labelled containers. Clean contaminated surface thoroughly.
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Avoid contact with eyes and skin. Wash hands thoroughly after handling. Do not eat, drink or smoke when using this product.
Keep container tightly closed in a dry and well-ventilated place. Keep cool. Keep in properly labelled containers. Keep away from heat and sources of ignition.
Wash hands thoroughly after handling. Do not eat, drink or smoke when using this product.
Keep away from heat and sources of ignition.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Ensure adequate ventilation, especially in confined areas.
Impervious gloves
Safety glasses with side-shields
No personal respiratory protective equipment normally required.
Usual safety precautions while handling the product will provide adequate protection against this potential effect
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Stable under normal conditions
Not applicable
None under normal processing. Hazardous polymerization does not occur.
Heat, flames and sparks
Strong oxidising agents
None under normal processing
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for MICROLUBE GL 261?
The signal word is no signal word.
What is the physical form of MICROLUBE GL 261?
MICROLUBE GL 261 is a solid appearing as paste with yellow color. It has mild odor.
What is MICROLUBE GL 261 used for?
Lubricant.
What are the hazard statements for MICROLUBE GL 261?
This substance has 1 hazard statement:
- The product contains no substances which at their given concentration, are considered to be hazardous to health
What is the melting point of MICROLUBE GL 261?
The melting point is No information available and the boiling point is No information available.