Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- DUOMEEN TDO
- Chemical Name
- Amines, N-C16-C18-alkyl-(evennumbered, C18 unsaturated) propane-1,3-diaminium di[(9Z)-octadec-9-enoate]
Regulatory Identifiers
- CAS Number
- N/A
- REACH No.
- 01-2119974117-33-0000
Identified Uses
Specific use(s): Refer to attached exposure scenario Annex.
Manufacturers & Suppliers
Nouryon Surface Chemistry AB
manufacturer
Stenunge Alle 3 SE 444 85 Stenungsund Sweden
+4630385000
Emergency Contacts
Kemiakuten, SE
020 99 60 00
emergency response number
+31 57 06 79 211
24 hours
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS07
GHS08
GHS09
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| N-(Tallow alkyl)-1,3-propanediamine oleate EC: 263-186-4 | 61791-53-5 | 90 - 100% | Yes |
First Aid Measures
Emergency procedures for chemical exposure incidents
Obtain medical attention immediately.
Take off contaminated clothing and shoes immediately. Carefully remove paste or solidified product. Wash skin immediately with 0,5 % acetic acid in water, and then with soap and water. If skin irritation persists, call a physician.
Symptoms: Skin irritation, if untreated may be prolonged and serious (eg necrosis).
In case of contact with eyes, rinse immediately with 0.5% acetic acid in water for a few minutes, followed by rinsing with plenty of water for as long as possible. Eyelids should be held away from the eyeball to ensure thorough rinsing. Get medical attention immediately. Continue to rinse during transport. Remove contact lenses. Protect unharmed eye. Keep eye wide open while rinsing.
Symptoms: Causes serious eye irritation.
Clean mouth with water and drink afterwards plenty of water. Never give anything by mouth to an unconscious person. Obtain medical attention.
Immediate Medical Attention
Obtain medical attention immediately for inhalation, eye contact, and ingestion.
Medical Treatment
This may be prevented by early treatment with medium strength corticosteroids.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Use extinguishing measures that are appropriate to local circumstances and the surrounding environment.
High volume water jet
Treat as oil fire.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Evacuate personnel to safe areas. Only qualified personnel equipped with suitable protective equipment may intervene. Prevent unauthorised persons entering the zone.
Do not flush into surface water or sanitary sewer system. If the product contaminates rivers and lakes or drains inform respective authorities.
Pick up and arrange disposal without creating dust.
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
For personal protection see section 8. Avoid formation of respirable particles. Avoid contact with skin, eyes and clothing. Smoking, eating and drinking should be prohibited in the application area.
Keep container tightly closed in a dry and well-ventilated place. Avoid elevated temperatures.
Smoking, eating and drinking should be prohibited in the application area.
Provide appropriate exhaust ventilation at places where dust is formed.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Provide eyewash station and safety shower. Keep solutions of 0.5% acetic acid in water close at hand.
Nitrile rubber butyl-rubber
Tightly fitting safety goggles
In the case of dust, vapour or aerosol formation use a respirator with an approved filter. Wear full face mask supplied with: Combination filter: ABEKP.
Protective suit
Do not flush into surface water or sanitary sewer system. If the product contaminates rivers and lakes or drains inform respective authorities.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Stable under recommended storage conditions.
Stable under normal conditions.
No dangerous reaction known under conditions of normal use.
None known.
Reacts with copper, aluminium, zinc and their alloys.
No hazardous decomposition products are known.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- 3077
- Shipping Name
- ENVIRONMENTALLY HAZARDOUS SUBSTANCE, SOLID, N.O.S. (Fatty amine derivative)
- Transport Class
- 9
- Packing Group
- III
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for DUOMEEN TDO?
The signal word is warning.
What is the physical form of DUOMEEN TDO?
DUOMEEN TDO is a paste with brown color. It has slight ammoniacal odor.
What is DUOMEEN TDO used for?
Specific use(s): Refer to attached exposure scenario Annex.
What are the hazard statements for DUOMEEN TDO?
This substance has 4 hazard statements:
- H315: Causes skin irritation.
- H319: Causes serious eye irritation.
- H373: May cause damage to organs (Gastrointestinal tract) through prolonged or repeated exposure.
- H410: Very toxic to aquatic life with long lasting effects.
What is the melting point of DUOMEEN TDO?
The melting point is 30 - 40 °C and the boiling point is > 250 °C.