Hexane

Remove to fresh air. If not breathing, give artificial respiration. Get medical attention if symptoms occur.

Symptoms: Risk of serious damage to the lungs (by aspiration).

Wash off immediately with plenty of water for at least 15 minutes. If skin irritation persists, call a physician.

Rinse immediately with plenty of water, also under the eyelids, for at least 15 minutes. Get medical attention.

Clean mouth with water and drink afterwards plenty of water. Do NOT induce vomiting. Call a physician or poison control center immediately. If vomiting occurs naturally, have victim lean forward.

CO₂, dry chemical, dry sand, alcohol-resistant foam. Water mist may be used to cool closed containers.

Do not use a solid water stream as it may scatter and spread fire.

Flammable. Risk of ignition. Vapors may form explosive mixtures with air. Vapors may travel to source of ignition and flash back. Containers may explode when heated.

Use personal protective equipment as required.

Do not flush into surface water or sanitary sewer system.

Soak up with inert absorbent material. Keep in suitable, closed containers for disposal.

Materials: inert absorbent material

Wear personal protective equipment/face protection. Do not get in eyes, on skin, or on clothing. Ensure adequate ventilation. Avoid ingestion and inhalation. Keep away from open flames, hot surfaces and sources of ignition. Use only non-sparking tools. To avoid ignition of vapors by static electricity discharge, all metal parts of the equipment must be grounded. Take precautionary measures against static discharges.

Keep containers tightly closed in a dry, cool and well-ventilated place.

Handle in accordance with good industrial hygiene and safety practice. Keep away from food, drink and animal feeding stuffs. Do not eat, drink or smoke when using this product. Remove and wash contaminated clothing and gloves, including the inside, before re-use. Wash hands before breaks and after work.

Keep away from open flames, hot surfaces and sources of ignition. Use only non-sparking tools.

Ensure adequate ventilation, especially in confined areas. Ensure that eyewash stations and safety showers are close to the workstation location. Use explosion-proof electrical/ventilating/lighting equipment. Wherever possible, engineering control measures such as the isolation or enclosure of the process, the introduction of process or equipment changes to minimise release or contact, and the use of properly designed ventilation systems, should be adopted to control hazardous materials at source

Protective gloves. Glove material: Nitrile rubber (> 480 minutes, 0.38 - 0.56 mm, Level 6, As tested under EN374-3), Viton (R) (> 480 minutes, 0.7 mm, EN 374), Neoprene gloves (< 180 minutes, 0.45 mm). Inspect gloves before use. Please observe the instructions regarding permeability and breakthrough time which are provided by the supplier of the gloves. (Refer to manufacturer/supplier for information). Ensure gloves are suitable for the task: Chemical compatibility, Dexterity, Operational conditions, User susceptibility, e.g. sensitisation effects, also take into consideration the specific local conditions under which the product is used, such as the danger of cuts, abrasion. Remove gloves with care avoiding skin contamination.

Wear safety glasses with side shields (or goggles) (European standard - EN 166)

When workers are facing concentrations above the exposure limit they must use appropriate certified respirators. To protect the wearer, respiratory protective equipment must be the correct fit and be used and maintained properly. Large scale/emergency use: Use a NIOSH/MSHA or European Standard EN 136 approved respirator if exposure limits are exceeded or if irritation or other symptoms are experienced. Recommended Filter type: Organic gases and vapours filter Type A Brown conforming to EN14387. Small scale/Laboratory use: Use a NIOSH/MSHA or European Standard EN 149:2001 approved respirator if exposure limits are exceeded or if irritation or other symptoms are experienced. Recommended half mask:- Valve filtering: EN405; or; Half mask: EN140; plus filter, EN 141. When RPE is used a face piece Fit Test should be conducted

Wear appropriate protective gloves and clothing to prevent skin exposure.

Prevent product from entering drains. Do not allow material to contaminate ground water system.

Stable under normal conditions.

None known, based on information available

None under normal processing. Hazardous Polymerization No information available.

Incompatible products. Heat, flames and sparks. Exposure to light. Keep away from open flames, hot surfaces and sources of ignition.

Incompatible products

Carbon monoxide (CO). Carbon dioxide (CO2)