Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- Oosafe® Disinfectant for CO₂ Incubators and laminar Flow Hoods
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
02 Private area and public health area disinfectants and other public health area biocidical products especially suited for IVF laboratories
Manufacturers & Suppliers
Sparmed Aps
national supplier
Toppevadvej 34 - 38, DK-3660 Stenlose, Denmark
+45 39 40 25 03
IC PRODUCTS SA
manufacturer
Via dei Paoli 25, CH-6648 Minusio
Emergency Contacts
Emergency Contact
+41 91 743 67 61
Swiss toxicological information center (STIZ)
145
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Quaternary ammonium compounds, benzyl-C12-C16--alkyldimethyl, chlorides EC: 270-325-2 | 68424-85-1 | 0.01% | Yes |
For the full text of the H-Statements mentioned in this Section, see Section 15. For the full text of the R-phrases mentioned in this Section, see Section 15.
First Aid Measures
Emergency procedures for chemical exposure incidents
Supply fresh air; consult doctor in case of complains.
The product is not irritating for the skin.
Rinse immediately with plenty of water, also under the eyelids, for at least 15 minutes. Call a physician immediately.
Call a physician immediately. Clean mouth with water and drink afterwards plenty of water. Do not induce vomiting without medical advice. Never give anything by mouth to an unconscious person.
Immediate Medical Attention
Call a physician immediately.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Dry powder, water spray, foam.
Heating or fire can release toxic gas.
Firefighter Protection
In the event of fire, wear self-contained breathing apparatus.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Dilute with plenty of water. Do not allow to enter sewers / surface or ground water.
Absorb with liquid-binding material ( sand, diatomite, acid binders, universal binders, sawdust ).
Materials: sand, diatomite, acid binders, universal binders, sawdust
Related Products
Similar products with comparable safety profiles
Oosafe® Disinfectant for CO₂ Incubators and Laminar Flow Hoods
---
Oosafe® Disinfectant
---
Oosafe® Laboratory Surface Disinfectant
---
Oosafe® Laboratory Surface Disinfectant
---
Oosafe® Hand Disinfectant
---
Oosafe Hand Disinfectant
---
ECO Disinfect
---
Orotol® plus Disinfection of suction system
---
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
No special measures required if used properly
Keep away from heat and direct sun radiations
No special measures required
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
No further data; see item 7.
Not required.
Not required.
Not required.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
No dangerous reactions known if used according to specifications.
No decomposition if used according to specifications.
No dangerous decomposition products known if used according to specifications.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for Oosafe® Disinfectant for CO₂ Incubators and laminar Flow Hoods?
The signal word is no signal word.
What is the physical form of Oosafe® Disinfectant for CO₂ Incubators and laminar Flow Hoods?
Oosafe® Disinfectant for CO₂ Incubators and laminar Flow Hoods is a liquid with colourless color. It has odourless odor.
What is Oosafe® Disinfectant for CO₂ Incubators and laminar Flow Hoods used for?
02 Private area and public health area disinfectants and other public health area biocidical products especially suited for IVF laboratories
What is the melting point of Oosafe® Disinfectant for CO₂ Incubators and laminar Flow Hoods?
The melting point is 0 °C and the boiling point is 100 °C.