Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- Oosafe® Laboratory Surface Disinfectant
- Product Code
- OODSF-0050; OODSF-02000; OODSF-10000
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Disinfectant for surfaces; Product type 2: Private area and public health area disinfectants and other public health area biocidal products especially suited for IVF laboratories; For disinfection and cleaning of laboratory surfaces. Especially is suitable for IVF laboratories. Only for professional use.
Manufacturers & Suppliers
Sparmed Aps
manufacturer
Ryttermarken 2, DK-3520, Farum, Denmark
Emergency Contacts
Danish Poison Line
+45 82 12 12 12
Emergency Contact
+45 39 40 25 03
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
Mixture of substances listed above with non-hazardous additions.
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| N,N-didecyl-N-methyl-poly(oxethyl)ammonium priopionate | 94667-33-1 | 6.3% | No |
For the wording of the listed risk-phrases refer to section 15
Notes
Dangerous components: No dangerous components.
First Aid Measures
Emergency procedures for chemical exposure incidents
Supply fresh air; consult doctor in case of complaints
The product is not irritating for the skin
Rinse open eye for 10min under running water. Force to open eyelids. Consult a doctor if irritation persists.
Call a physician immediately. Clean mouth with water and drink afterwards plenty of water. Do not induce vomiting without medical advice. Never give anything by mouth to an unconscious person.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Dry powder, water spray, foam.
Heating or fire can release toxic gas.
Use water spray to cool unopened containers.
Firefighter Protection
In the event of fire, wear self-contained breathing apparatus.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Not required
Dilute with plenty of water.
Absorb with liquid- binding material
Materials: sand, diatomite, acid binders, universal binders, sawdust
Related Products
Similar products with comparable safety profiles
Oosafe® Laboratory Surface Disinfectant
---
Oosafe® Disinfectant
---
Oosafe® Hand Disinfectant
---
Oosafe Hand Disinfectant
---
Oosafe® Disinfectant for CO₂ Incubators and Laminar Flow Hoods
---
Oosafe® Disinfectant for CO₂ Incubators and laminar Flow Hoods
---
Pal Surface Disinfectant Wipes
---
5180 Surface Disinfectant Cleaner 1I ALL
UFI: 4JA2-V00H-000M-SK9A
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
No special measures required if used properly
Keep away from heat and direct sunlight.
No special measures required
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
The selection of suitable gloves does not only depend on the material, but also on further marks of quality and varies from manufacturer to manufacturer. As the product is a preparation of several substances, the resistance of the glove material cannot be calculated in advance and has therefore to be checked prior to the application. Penetration time of glove material: The exact break through time has to be found out by the manufacturer of the protective gloves and has to be observed.
Goggles recommended during refilling.
Not required
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
No decomposition if used according to specifications;
No dangerous reactions known if used according to specifications;
See. Section 7;
No dangerous decomposition products known if used according to specifications.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for Oosafe® Laboratory Surface Disinfectant?
The signal word is no signal word.
What is the physical form of Oosafe® Laboratory Surface Disinfectant?
Oosafe® Laboratory Surface Disinfectant is a liquid with according to product specification color. It has slightly aromatic odor.
What is Oosafe® Laboratory Surface Disinfectant used for?
Disinfectant for surfaces; Product type 2: Private area and public health area disinfectants and other public health area biocidal products especially suited for IVF laboratories; For disinfection and cleaning of laboratory surfaces. Especially is suitable for IVF laboratories. Only for professional use.
What is the melting point of Oosafe® Laboratory Surface Disinfectant?
The melting point is undetermined and the boiling point is 100°C.