NextSDS Logo
Safety Data Sheet EN

INTERTHANE 990 SIGNAL BLACK PART A

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report.

Get Free Audit
01

Identification

Product identifiers, regulatory numbers, and supplier information

Product Information

Product Name
INTERTHANE 990 SIGNAL BLACK PART A
Product Code
PHZ903

Regulatory Identifiers

CAS Number
N/A

Identified Uses

Refer Technical Data Sheet.

Manufacturers & Suppliers

I

International Paint Singapore Pte Ltd

manufacturer

I

International Paint Singapore Pte Ltd

manufacturer

3 Neythal Road, Jurong Town, Singapore 628570

+65 6261 5033

Emergency Contacts

Poisons Advice

+65 6261 5033

24 hour

02

Hazard Identification

GHS classification, signal word, pictograms, and hazard statements

Classified warning

Hazard Classifications

Flam. Liq. Cat. 3 H226
Skin Irrit. Cat. 2 H315
Eye Irrit. Cat. 2 H319
STOT SE Cat. 3 H336

GHS Pictograms

GHS02 - Flammable

GHS02

GHS07 - Health hazard

GHS07

Hazard Statements

H226 Flammable liquid and vapour.
H315 Causes skin irritation.
H319 Causes serious eye irritation.
H335 May cause respiratory irritation.

Precautionary Statements

P210 Keep away from heat / sparks / open flames / hot surfaces - No smoking.
P235 Keep cool.
P240 Ground / bond container and receiving equipment.
P241 Use explosion-proof electrical / ventilating / light / equipment.
P242 Use only non-sparking tools.
P243 Take precautionary measures against static discharge.
P260 Do not breathe mist / vapours / spray.
P261 Avoid breathing dust / fume / gas / mist / vapours / spray.
P262 Do not get in eyes, on skin, or on clothing.
P264 Wash thoroughly after handling.
P271 Use only outdoors or in a well-ventilated area.
P273 Avoid release to the environment.
P280 Wear protective gloves / eye protection / face protection.
P321 Specific treatment (see information on this label).
P331 Do NOT induce vomiting.
P362 Take off contaminated clothing and wash before reuse.
P405 Store locked up.
P501 Dispose of contents / container in accordance with local / national regulations.
IF SWALLOWED: Immediately call a POISON CENTER or doctor / physician.
IF ON SKIN: Wash with soap and water.
IF ON SKIN (or hair): Remove / Take off immediately all contaminated clothing. Rinse skin with water / shower.
IF INHALED: Call a POISON CENTER or doctor / physician if you feel unwell.
IF IN EYES: Rinse continuously with water for several minutes. Remove contact lenses if present and easy to do - continue rinsing.
If eye irritation persists: Get medical advice / attention.
IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing.
In case of fire: Use alcohol resistant foam, CO2, powder, water spray for extinction. Do not use water jet.
Store in a well ventilated place. Keep container tightly closed.

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report

Free Audit
03

Composition / Information on Ingredients

Chemical components, concentration ranges, and hazardous substance identification

Type mixture
Chemical Name CAS Number Concentration Hazardous
Acrylic Polymer --- 25 - 50% No
Solvent naphtha (petroleum), light aromatic 0064742-95-6 10 - 25% Yes
Xylene 0001330-20-7 10 - 25% Yes
Carbon black 0001333-86-4 2.5 - 10% No
Ethylbenzene 0000100-41-4 2.5 - 10% Yes
2-Methoxy-1-Methylethyl Acetate 0000108-65-6 1 - 2.5% Yes
Bis(pentamethyl-4-piperidyl)sebacate 0041556-26-7 1% Yes
04

First Aid Measures

Emergency procedures for chemical exposure incidents

Inhalation

Remove to fresh air, keep patient warm and at rest. If breathing is irregular or stopped, give artificial respiration. If unconscious place in the recovery position and obtain immediate medical attention. Give nothing by mouth.

Skin contact

Remove contaminated clothing. Wash skin thoroughly with soap and water or use a recognised skin cleanser. Do NOT use solvents or thinners.

Eye contact

Irrigate copiously with clean fresh water for at least 10 minutes, holding the eyelids apart and seek medical attention.

Ingestion

If accidentally swallowed obtain immediate medical attention. Keep at rest. Do NOT induce vomiting.

Immediate Medical Attention

In all cases of doubt, or when symptoms persist, seek medical attention. If unconscious, obtain immediate medical attention. If accidentally swallowed, obtain immediate medical attention.

05

Firefighting Measures

Extinguishing media, specific hazards, and firefighter protection

Suitable media

alcohol resistant foam, CO2, powder, water spray

Unsuitable media

water jet

Specific hazards

Fire will produce dense black smoke.

Instructions

Cool closed containers exposed to fire by spraying them with water.

Firefighter Protection

Avoid exposure and use breathing apparatus as appropriate.

06

Accidental Release Measures

Spill cleanup procedures, containment, and environmental protection

Emergency procedures

Remove sources of ignition, do not turn lights or unprotected electrical equipment on or off. In case of a major spill or spillage in a confined space evacuate the area and check that solvent vapour levels are below the Lower Explosive Limit before re-entering. Ventilate the area and avoid breathing vapours. Take the personal protective measures listed in section 8.

Environmental

Do not allow spills to enter drains or watercourses.

Cleanup methods

Clean, preferably with a detergent. Do not use solvents.

Materials: detergent

Related Products

Similar products with comparable safety profiles

07

Handling and Storage

Safe handling precautions, storage conditions, and workplace requirements

Handling

Handle containers carefully to prevent damage and spillage. Naked flames and smoking should not be permitted in storage areas.

Storage

Handle containers carefully to prevent damage and spillage. Naked flames and smoking should not be permitted in storage areas.

Hygiene

Smoking, eating and drinking should be prohibited in all preparation and application areas.

Fire prevention

Naked flames and smoking should not be permitted in storage areas.

08

Exposure Controls / PPE

Occupational exposure limits, engineering controls, and protective equipment

Engineering

Provide adequate ventilation. Where reasonably practicable this should be achieved by the use of local exhaust ventilation and good general extraction.

Hands

Gloves of an appropriate material should be worn during mixing and application.

Eyes

Wear safety eyewear, e.g. safety spectacles, goggles or visors to protect against the splash of liquids. Eyewear should comply with the appropriate standard. Wear a full face shield if mixing or pouring operations pose a risk of splashes.

Respiratory

If these are not sufficient to maintain concentrations of particulates and any vapour below occupational exposure limits suitable respiratory protection must be worn. When concentrations exceed the exposure limits shown above workers must wear appropriate approved respirators. Provision of other controls such as exhaust ventilation should be considered if practical.

Skin/Body

Overalls which cover the body, arms and legs should be worn. Skin should not be exposed. Barrier creams may help to protect areas which are difficult to cover such as the face and neck. They should however not be applied once exposure has occurred. Petroleum jelly based types such as Vaseline should not be used.

09

Physical and Chemical Properties

Appearance, physical state, melting point, boiling point, and material characteristics

Physical State
liquid
Freezing Point
---
Relative Evaporation Rate
---
Odor
Smell of Solvent
Auto Ignition Temperature
Not Measured
Solidification Point
---
Lower Explosive Limit
Lower Explosive Limit: 1.1 Xylene
Solubility In Water
Immiscible
Form
---
Metal Corrosion
---
Melting Point
Not Measured
Decomposition Temperature
Not Measured
Physical State Data
liquid
Flash Point
34 °C
Solubility In Fat
---
Density
---
Properties Status
---
Upper Explosive Limit
Upper Explosive Limit: 6.6 Xylene
Solubility
---
Explosive Limits
---
Vapor Pressure
Not Measured
Vapor Density
Heavier than air.
Flammability
Not Applicable
Appearance
---
Softening Point
---
Relative Density
1.16
Ph
---
Dynamic Viscosity
---
Kinematic Viscosity
---
Odor Threshold
Not Measured
Evaporation Rate
Not Measured
Crystallisation Point
---
Colour
Black
Voc Content
---
Partition Coefficient
Not Measured
Boiling Point
108 °C
Cloud Point
---
Bulk Density
---
Colour Intensity
---
Molecular Weight
---
State Under Standard Conditions
---
10

Stability and Reactivity

Chemical stability, hazardous reactions, and incompatible materials

Stability

Stable under recommended storage and handling conditions (see section 7).

Reactivity

No data available

Hazardous reactions

Keep away from oxidising agents, strongly alkaline and strongly acid materials in order to avoid possible exothermic reactions.

Avoid

high temperatures

Incompatible

oxidising agents, strongly alkaline and strongly acid materials

Decomposition

carbon monoxide, carbon dioxide, oxides of nitrogen and smoke

12

Ecological Information

Environmental toxicity, biodegradation, and bioaccumulation data

The data for this section has not been processed yet.

13

Disposal Considerations

Waste treatment methods, disposal recommendations, and waste codes

The data for this section has not been processed yet.

14

Transport Information

UN numbers, shipping names, transport classes, and regulatory requirements

UN Number
1263
Shipping Name
Paint
Transport Class
3
Packing Group
III
15

Regulatory Information

Chemical regulations, safety assessments, and compliance status

The data for this section has not been processed yet.

?

Frequently Asked Questions

Common questions about safety, handling, and properties

What is the hazard signal word for INTERTHANE 990 SIGNAL BLACK PART A?

The signal word is warning.

What is the physical form of INTERTHANE 990 SIGNAL BLACK PART A?

INTERTHANE 990 SIGNAL BLACK PART A is a liquid with black color. It has smell of solvent odor.

What is INTERTHANE 990 SIGNAL BLACK PART A used for?

Refer Technical Data Sheet.

What are the hazard statements for INTERTHANE 990 SIGNAL BLACK PART A?

This substance has 4 hazard statements:

  • H226: Flammable liquid and vapour.
  • H315: Causes skin irritation.
  • H319: Causes serious eye irritation.
  • H335: May cause respiratory irritation.

What is the melting point of INTERTHANE 990 SIGNAL BLACK PART A?

The melting point is Not Measured and the boiling point is 108 °C.