NextSDS Logo
Safety Data Sheet EN

POWERCLEAN STANDARD

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report.

Get Free Audit
01

Identification

Product identifiers, regulatory numbers, and supplier information

Product Information

Product Name
POWERCLEAN STANDARD
Product Form
Pressurised gas cleaning spray, flammable 400 ml spray can
Product Code
579619

Regulatory Identifiers

CAS Number
N/A

Identified Uses

Pressurised gas cleaning spray

Manufacturers & Suppliers

DURABLE Hunke & Jochheim GmbH & Co. KG logo

DURABLE Hunke & Jochheim GmbH & Co. KG

manufacturer

Westfalenstraße 77 – 79, 58636 Iserlohn, Germany

+49 (0) 2371 662 0

http://www.durable.de

D

DURABLE Hunke & Jochheim GmbH & Co. KG

manufacturer

+49 (0) 2371 662 350

Emergency Contacts

Giftnotruf Berlin

+49 30 19240

02

Hazard Identification

GHS classification, signal word, pictograms, and hazard statements

Classified danger

Hazard Classifications

Aerosol Cat. 1 H222

GHS Pictograms

GHS02 - Flammable

GHS02

Hazard Statements

H222 Extremely flammable aerosol.
H229 Pressurised container: May burst if heated.

Precautionary Statements

P102 Keep out of reach of children.
P210 Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking.
P211 Do not spray on an open flame or other ignition source.
P251 Do not pierce or burn, even after use.
P410 + P412 Protect from sunlight. Do not expose to temperatures exceeding 50 °C.

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report

Free Audit
03

Composition / Information on Ingredients

Chemical components, concentration ranges, and hazardous substance identification

Type mixture
Chemical Name CAS Number Concentration Hazardous
propane EC: 200-827-9 74-98-6 25 - 50% Yes
isobutane EC: 200-857-2 75-28-5 25 - 50% Yes
butane EC: 203-448-7 106-97-8 25 - 50% Yes
04

First Aid Measures

Emergency procedures for chemical exposure incidents

Inhalation

Provide fresh air. If breathing is irregular or stopped, immediately seek medical assistance and start first aid actions.

Symptoms: Dizziness.

Skin contact

Gently wash with plenty of soap and water.

Symptoms: Contact with the product can cause burns and/or frostbite.

Eye contact

Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical advice/attention.

Ingestion

Remove person to fresh air and keep comfortable for breathing.

Immediate Medical Attention

In all cases of doubt, or when symptoms persist, seek medical advice. If breathing is irregular or stopped, immediately seek medical assistance. If eye irritation persists: Get medical advice/attention.

Medical Treatment

None.

05

Firefighting Measures

Extinguishing media, specific hazards, and firefighter protection

Suitable media

water spray, water mist, foam, dry extinguishing powder, carbon dioxide (CO2)

Unsuitable media

water jet

Specific hazards

Contains gas under pressure; may explode if heated.

Instructions

Co-ordinate firefighting measures to the fire surroundings. Fight fire with normal precautions from a reasonable distance.

06

Accidental Release Measures

Spill cleanup procedures, containment, and environmental protection

Emergency procedures

Remove persons to safety. Ventilate affected area.

Environmental

In case of formation of gases/vapours/mists suppress with water spray

Related Products

Similar products with comparable safety profiles

07

Handling and Storage

Safe handling precautions, storage conditions, and workplace requirements

Handling

Use only in well-ventilated areas. Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Prevent from heating up above 50 °C/122 °F.

Storage

Prevent from heating up above 50 °C/122 °F. Protect from sunlight.

Hygiene

Do not eat, drink and smoke in work areas. Wash hands after use. Preventive skin protection (barrier creams/ointments) is recommended. Remove contaminated clothing and protective equipment before entering eating areas.

Fire prevention

Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking.

08

Exposure Controls / PPE

Occupational exposure limits, engineering controls, and protective equipment

Engineering

Use local and general ventilation.

Hands

Material: NBR: acrylonitrile-butadiene rubber. Material thickness: no information available. Breakthrough times: no information available. Wear suitable gloves. Chemical protection gloves are suitable, which are tested according to EN 374. Check leak-tightness/impermeability prior to use. For special purposes, it is recommended to check the resistance to chemicals of the protective gloves mentioned above together with the supplier of these gloves.

Eyes

Wear eye/face protection. (EN 166).

Respiratory

In case of inadequate ventilation wear respiratory protection. During spraying wear suitable respiratory equipment. Type: AX (gas filters and combined filters against low-boiling point organic compounds, colour code: Brown). (EN 136, EN 140, EN 14387, EN 143, EN 149).

Environmental

Use appropriate container to avoid environmental contamination. Keep away from drains, surface and ground water.

09

Physical and Chemical Properties

Appearance, physical state, melting point, boiling point, and material characteristics

Flash Point
-70 °C
Decomposition Temperature
not relevant
Upper Explosive Limit
9.5 vol%
Dynamic Viscosity
---
Odor
odourless
Physical State Data
aerosol
Relative Evaporation Rate
---
Colour
colourless
Explosive Limits
---
Ph
not determined
Colour Intensity
---
Melting Point
-182 °C
Evaporation Rate
---
State Under Standard Conditions
---
Odor Threshold
1,200 ppm
Appearance
---
Voc Content
---
Molecular Weight
---
Solidification Point
---
Form
---
Solubility In Fat
---
Lower Explosive Limit
1.5 vol%
Flammability
flammable aerosol in accordance with GHS criteria
Properties Status
---
Density
0.54 g/ml at 20 °C
Relative Density
---
Crystallisation Point
---
Freezing Point
---
Kinematic Viscosity
---
Softening Point
---
Physical State
gaseous (spray aerosol)
Solubility In Water
not determined
Partition Coefficient
not determined
Metal Corrosion
---
Solubility
---
Bulk Density
---
Boiling Point
-40 – -1 °C
Cloud Point
---
Auto Ignition Temperature
not applicable (aerosol)
Vapor Density
---
Vapor Pressure
1,200 – 7,300 hPa
10

Stability and Reactivity

Chemical stability, hazardous reactions, and incompatible materials

Stability

The material is stable under normal ambient and anticipated storage and handling conditions of temperature and pressure.

Reactivity

Risk of ignition.

Hazardous reactions

In case of insufficient ventilation and/or in use, may form flammable/explosive vapour-air mixture.

Avoid

Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Do not spray on an open flame or other ignition source. Contains gas under pressure; may explode if heated. Protect from sunlight.

Incompatible

There is no additional information.

Decomposition

Reasonably anticipated hazardous decomposition products produced as a result of use, storage, spill and heating are not known. Hazardous combustion products: see section 5.

12

Ecological Information

Environmental toxicity, biodegradation, and bioaccumulation data

The data for this section has not been processed yet.

13

Disposal Considerations

Waste treatment methods, disposal recommendations, and waste codes

The data for this section has not been processed yet.

14

Transport Information

UN numbers, shipping names, transport classes, and regulatory requirements

UN Number
1950
Shipping Name
AEROSOLS
15

Regulatory Information

Chemical regulations, safety assessments, and compliance status

The data for this section has not been processed yet.

?

Frequently Asked Questions

Common questions about safety, handling, and properties

What is the hazard signal word for POWERCLEAN STANDARD?

The signal word is danger.

What is the physical form of POWERCLEAN STANDARD?

POWERCLEAN STANDARD is a gaseous (spray aerosol) with colourless color. It has odourless odor.

What is POWERCLEAN STANDARD used for?

Pressurised gas cleaning spray

What are the hazard statements for POWERCLEAN STANDARD?

This substance has 2 hazard statements:

  • H222: Extremely flammable aerosol.
  • H229: Pressurised container: May burst if heated.

What is the melting point of POWERCLEAN STANDARD?

The melting point is -182 °C and the boiling point is -40 – -1 °C.