Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- LOCTITE SI 5145 CQ/BN EN/DE
- Product Form
- Silicone sealant
- Product Code
- 3125627
Regulatory Identifiers
- CAS Number
- N/A
Manufacturers & Suppliers
Henkel Corporation
manufacturer
One Henkel Way, Rocky Hill, Connecticut 06067
+1 (860) 571-5100
http://www.henkelna.com
Emergency Contacts
Poison Control Center
1-877-671-4608
Poison Control Center
1-303-592-1711
CHEMTREC
1-800-424-9300
CHEMTREC
1-703-527-3887
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
GHS Pictograms
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
* Exact percentages may vary or are trade secret. Concentration range is provided to assist users in providing appropriate protections.
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Silica, amorphous, treated | 68909-20-6 | 10 - 30% | Yes |
| Dimethoxydimethylsilane | 1112-39-6 | 1 - 5% | Yes |
IDH number: 3125627 Product name: LOCTITE SI 5145 CQ/BN EN/DE
First Aid Measures
Emergency procedures for chemical exposure incidents
Move to fresh air. If symptoms develop and persist, get medical attention.
Wipe off paste with paper towel or cloth. Wash with soap and water. If skin irritation persists, call a physician.
Rinse immediately with plenty of water, also under the eyelids, for at least 15 minutes. If eye irritation persists, consult a specialist.
Do not induce vomiting. Get medical attention.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Foam, dry chemical or carbon dioxide.
High volume water jet.
Prevent inhalation of fumes and gases. In case of fire, keep containers cool with water spray.
Firefighter Protection
Wear self-contained breathing apparatus and full protective clothing, such as turn-out gear.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Use personal protection recommended in Section 8, isolate the hazard area and deny entry to unnecessary and unprotected personnel.
Maintain good ventilation for large spills.
Do not allow material to contaminate ground water system.
Scrape up as much material as possible. Place scrap material in a well ventilated area and allow to cure to rubber.
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Prevent contact with eyes, skin and clothing. Do not breathe vapor and mist. Wash thoroughly after handling.
Store in a dry area below 90° F.
Wash thoroughly after handling.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Ensure adequate ventilation, especially in confined areas. Avoid naked flames, sparking and sources of ignition. Prevent electrostatic charge build-up by using common bonding and grounding techniques.
Use impermeable gloves
Safety goggles or safety glasses with side shields.
Use a NIOSH approved supplied air respirator with an organic cartridge if the potential to exceed established exposure limits exists.
protective clothing as necessary to prevent skin contact.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Stable under normal conditions of storage and use.
Not available.
None under normal processing.
Exposure to moisture. Heat, flames, sparks and other sources of ignition.
Acids. Bases. Oxidizing agents. Moisture.
Oxides of carbon. Oxides of silicon. Formaldehyde. Contact with water liberates methanol. Irritating vapors.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for LOCTITE SI 5145 CQ/BN EN/DE?
The signal word is no signal word.
What is the physical form of LOCTITE SI 5145 CQ/BN EN/DE?
LOCTITE SI 5145 CQ/BN EN/DE is a solid with translucent color. It has slight, alcoholic odor.
What is the solubility of LOCTITE SI 5145 CQ/BN EN/DE?
Polymerises in presence of water. Water; Not determined Acetone
What is the melting point of LOCTITE SI 5145 CQ/BN EN/DE?
The melting point is -40 °C (-40°F) and the boiling point is 375 °C (707°F).