NextSDS Logo
Safety Data Sheet EN

LOCTITE CR 821 ECO B

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report.

Get Free Audit
01

Identification

Product identifiers, regulatory numbers, and supplier information

Product Information

Product Name
LOCTITE CR 821 ECO B
Product Code
2951044

Regulatory Identifiers

CAS Number
N/A

Manufacturers & Suppliers

Henkel Corporation logo

Henkel Corporation

manufacturer

One Henkel Way, Rocky Hill, Connecticut 06067

+1 (860) 571-5100

www.henkelna.com

Emergency Contacts

Poison Control Center

1-877-671-4608

Poison Control Center

1-303-592-1711

CHEMTREC

1-800-424-9300

CHEMTREC

1-703-527-3887

02

Hazard Identification

GHS classification, signal word, pictograms, and hazard statements

Classified danger

Hazard Classifications

Acute Tox. Cat. 4
Skin Irrit. Cat. 2
Eye Irrit. Cat. 2A
Resp. Sens. Cat. 1
Skin Sens. Cat. 1
STOT SE Cat. 3
STOT RE Cat. 1

GHS Pictograms

GHS07 - Health hazard

GHS07

GHS08 - Serious health hazard

GHS08

Hazard Statements

H315 CAUSES SKIN IRRITATION.
H317 MAY CAUSE AN ALLERGIC SKIN REACTION.
H319 CAUSES SERIOUS EYE IRRITATION.
H332 HARMFUL IF INHALED.
H334 MAY CAUSE ALLERGY OR ASTHMA SYMPTOMS OR BREATHING DIFFICULTIES IF INHALED.
H335 MAY CAUSE RESPIRATORY IRRITATION.
H372 CAUSES DAMAGE TO ORGANS THROUGH PROLONGED OR REPEATED EXPOSURE.

Precautionary Statements

P260 Do not breathe vapors, mist, or spray.
P264 Wash affected area thoroughly after handling.
P270 Do not eat, drink or smoke when using this product.
P271 Use only outdoors or in a well-ventilated area.
P272 Contaminated work clothing should not be allowed out of the workplace.
P280 Wear protective gloves, eye protection, and face protection.
P284 [In case of inadequate ventilation] wear respiratory protection.
P302 + P352 IF ON SKIN: Wash with plenty of water.
P305 + P351 + P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
P333 + P313 If skin irritation or rash occurs: Get medical attention.
P337 + P313 If eye irritation persists: Get medical attention.
P342 + P311 If experiencing respiratory symptoms: Call a poison center or physician.
P362 + P364 Take off contaminated clothing and wash it before reuse.
P403 + P233 Store in a well-ventilated place. Keep container tightly closed.
P405 Store locked up.
P501 Dispose of contents and/or container according to Federal, State/Provincial and local governmental regulations.
IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing. Call a POISON CENTER or physician if you feel unwell.

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report

Free Audit
03

Composition / Information on Ingredients

Chemical components, concentration ranges, and hazardous substance identification

Type uvcb
Chemical Name CAS Number Concentration Hazardous
Diphenylmethane diisocyanate, isomers and homologs 9016-87-9 80 - 100% Yes
04

First Aid Measures

Emergency procedures for chemical exposure incidents

Inhalation

If not breathing, give artificial respiration. If breathing is difficult, oxygen should be administered by qualified personnel. Move to fresh air.

Symptoms: Asthmatic-type symptoms may develop and may be immediate or delayed up to several hours. Extreme asthmatic reactions can be life threatening.

Skin contact

Remove contaminated clothing and shoes. Wipe off paste with paper towel or cloth. Rinse with running water and soap. Wash contaminated clothing before reuse. Thoroughly clean shoes before reuse. Discard any shoes or clothing items that cannot be decontaminated.

Eye contact

Rinse immediately with plenty of water, also under the eyelids, for at least 15 minutes.

Ingestion

DO NOT induce vomiting unless directed to do so by medical personnel. Never give anything by mouth to an unconscious person.

Immediate Medical Attention

Seek medical attention immediately (for eye contact and ingestion). If symptoms persist, seek medical advice (for inhalation).

05

Firefighting Measures

Extinguishing media, specific hazards, and firefighter protection

Suitable media

Use extinguishing measures appropriate to local circumstances and the surrounding environment. Foam, dry chemical or carbon dioxide.

Unsuitable media

Do not use high volume water jet.

Specific hazards

At higher temperatures isocyanate may be released. Sealed containers at elevated temperatures or contaminated with water may rupture explosively.

Instructions

Keep containers cool with water spray. Keep unnecessary personnel away.

Firefighter Protection

Wear self-contained breathing apparatus and full protective clothing, such as turn-out gear.

06

Accidental Release Measures

Spill cleanup procedures, containment, and environmental protection

Emergency procedures

Use personal protection recommended in Section 8, isolate the hazard area and deny entry to unnecessary and unprotected personnel. Evacuate and ventilate spill area; dike spill to prevent entry into water system; wear full protective equipment during clean-up.

Small spill

Cover spill area with suitable absorbent material. Saturate absorbent material with neutralization solution and mix. Wait 15 minutes. Collect material in open-head metal containers. Repeat applications of decontamination solution with scrubbing, followed by absorbent until surface is decontaminated. Check for surface contamination using suitable test kit. Apply lid loosely and allow containers to vent for 72 hours to let carbon dioxide (CO2) escape.

Large spill

Large quantities may be pumped into closed, but not sealed containers for disposal.

Environmental

Do not empty into drains / surface water / ground water.

Cleanup methods

Remove all sources of ignition. Evacuate and ventilate spill area; dike spill to prevent entry into water system; wear full protective equipment during clean-up.

Materials: suitable absorbent material, neutralization solution, decontamination solution

Related Products

Similar products with comparable safety profiles

07

Handling and Storage

Safe handling precautions, storage conditions, and workplace requirements

Handling

Prevent contact with eyes, skin and clothing. Do not breathe vapor and mist. Wear suitable protective clothing, gloves and eye/face protection.

Storage

Store original or opened drums absolutely dry and always close it air-tight. Keep container tightly closed and in a cool, well-ventilated place away from incompatible materials. Keep from freezing. Protect from direct sunlight.

Hygiene

Wash thoroughly after handling.

08

Exposure Controls / PPE

Occupational exposure limits, engineering controls, and protective equipment

09

Physical and Chemical Properties

Appearance, physical state, melting point, boiling point, and material characteristics

Upper Explosive Limit
Not available.
Dynamic Viscosity
160 - 240 mPa.s
Solidification Point
---
Relative Density
---
Softening Point
---
Colour Intensity
---
Evaporation Rate
Not available.
Solubility
Insoluble Water
Relative Evaporation Rate
---
Odor
Typical
Bulk Density
---
Flammability
Not applicable
Ph
Not applicable, Product reacts with water.
Physical State
Liquid
Solubility In Water
---
Density
---
Decomposition Temperature
Not available.
Partition Coefficient
Not available.
Colour
Brown
Properties Status
---
Odor Threshold
Not available.
Melting Point
Not applicable, Product is a liquid
Metal Corrosion
---
Flash Point
200 °C (392°F)
Explosive Limits
---
Auto Ignition Temperature
Not available.
Physical State Data
liquid
Kinematic Viscosity
200 mm2/s
Vapor Pressure
1 hPa (20 °C (68°F))
Cloud Point
---
Vapor Density
---
Freezing Point
---
State Under Standard Conditions
---
Solubility In Fat
---
Form
---
Voc Content
Not available.
Crystallisation Point
---
Molecular Weight
---
Appearance
---
Boiling Point
300 °C (572°F)
Lower Explosive Limit
Not available.
10

Stability and Reactivity

Chemical stability, hazardous reactions, and incompatible materials

Stability

Stable under normal conditions of storage and use.

Reactivity

Not available.

Hazardous reactions

Exothermic. Polymerization may occur at elevated temperature or in the presence of incompatible materials.

Avoid

Avoid moisture. Contamination with water. Extremes of temperature and direct sunlight. Container can be pressurised by carbon dioxide due to reaction with humid air and/or water. Protect from direct sunlight. Do not freeze.

Incompatible

Water. Moisture. Humid air and/or water will produce carbon dioxide which will pressurize the container. Amines. Alcohols. Strong acids and strong bases.

Decomposition

Upon decomposition, this product may yield gaseous nitrogen oxides, carbon monoxide, carbon dioxide and/or low molecular weight hydrocarbons. Hydrogen cyanide. Isocyanate vapors

12

Ecological Information

Environmental toxicity, biodegradation, and bioaccumulation data

The data for this section has not been processed yet.

13

Disposal Considerations

Waste treatment methods, disposal recommendations, and waste codes

The data for this section has not been processed yet.

14

Transport Information

UN numbers, shipping names, transport classes, and regulatory requirements

15

Regulatory Information

Chemical regulations, safety assessments, and compliance status

The data for this section has not been processed yet.

?

Frequently Asked Questions

Common questions about safety, handling, and properties

What is the hazard signal word for LOCTITE CR 821 ECO B?

The signal word is danger.

What is the physical form of LOCTITE CR 821 ECO B?

LOCTITE CR 821 ECO B is a liquid with brown color. It has typical odor.

What is the solubility of LOCTITE CR 821 ECO B?

Insoluble Water

What are the hazard statements for LOCTITE CR 821 ECO B?

This substance has 7 hazard statements:

  • H315: CAUSES SKIN IRRITATION.
  • H317: MAY CAUSE AN ALLERGIC SKIN REACTION.
  • H319: CAUSES SERIOUS EYE IRRITATION.
  • H332: HARMFUL IF INHALED.
  • H334: MAY CAUSE ALLERGY OR ASTHMA SYMPTOMS OR BREATHING DIFFICULTIES IF INHALED.
  • H335: MAY CAUSE RESPIRATORY IRRITATION.
  • H372: CAUSES DAMAGE TO ORGANS THROUGH PROLONGED OR REPEATED EXPOSURE.

What is the melting point of LOCTITE CR 821 ECO B?

The melting point is Not applicable, Product is a liquid and the boiling point is 300 °C (572°F).