Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- LOCTITE 407 LOW VISCOSITY known as 407 INSTANT ADHESIVE IN JP 50
- Product Code
- 29780
- Chemical Name
- Cyanoacrylate
Regulatory Identifiers
- CAS Number
- N/A
Manufacturers & Suppliers
Henkel Corporation
manufacturer
One Henkel Way, Rocky Hill, Connecticut 06067
+1 (860) 571-5100
http://www.henkelna.com
Emergency Contacts
Poison Control Center
1-877-671-4608
Poison Control Center
1-303-592-1711
CHEMTREC
1-800-424-9300
CHEMTREC
1-703-527-3887
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS07
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Ethyl 2-cyanoacrylate | 7085-85-0 | 80 - 100% | Yes |
| Phthalic anhydride | 85-44-9 | 0.1 - 1% | Yes |
IDH number: 243277 Product name: LOCTITE 407 LOW VISCOSITY known as 407 INSTANT ADHESIVE IN JP 50
Notes
* Exact percentages may vary or are trade secret. Concentration range is provided to assist users in providing appropriate protections.
First Aid Measures
Emergency procedures for chemical exposure incidents
Move to fresh air. If breathing is difficult, give oxygen. If not breathing, give artificial respiration. If symptoms develop and persist, get medical attention.
Do not pull bonded skin apart. Soak in warm soapy water. Gently peel apart using a blunt instrument. If skin is burned due to the rapid generation of heat by a large drop, seek medical attention. If lips are bonded, apply warm water to the lips and encourage wetting and pressure from saliva in mouth. Peel or roll lips apart. Do not pull lips apart with direct opposing force.
Symptoms: Skin burned due to the rapid generation of heat.
Immediately flush with plenty of water for at least 15 minutes. Get medical attention. If eyelids are bonded closed, release eyelashes with warm water by covering with a wet pad. Do not force eye open. Keep eye covered until debonding is complete, usually within 1-3 days.
Symptoms: Eyelids bonded closed, lachrymatory effect, abrasive damage if solid particles are trapped behind the eyelid.
Ensure breathing passages are not obstructed. Saliva will separate any solidified product in several hours. Prevent the patient from swallowing any separated mass.
Symptoms: Bond to the mouth.
Immediate Medical Attention
Seek medical attention if skin is burned, if eyelids are bonded (for abrasive damage), or if inhalation symptoms persist.
Medical Treatment
Surgery is not necessary to separate accidentally bonded tissues. Experience has shown that bonded tissues are best treated by passive, non-surgical first aid. If rapid curing has caused thermal burns they should be treated symptomatically after adhesive is removed.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Water spray (fog), foam, dry chemical or carbon dioxide.
Wear a self-contained breathing apparatus with a full face piece operated in pressure-demand or other positive pressure mode.
Firefighter Protection
Wear a self-contained breathing apparatus with a full face piece operated in pressure-demand or other positive pressure mode.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Isolate the hazard area and deny entry to unnecessary and unprotected personnel.
Do not allow product to enter sewer or waterways.
Do not use cloths for mopping up. Flood with water to complete polymerization and scrape off the floor.
Materials: water
Related Products
Similar products with comparable safety profiles
LOCTITE 408 INSTANT ADHESIVE known as Loctite 408 20g EN/CH/JP
---
LOCTITE 444 MED VISCOSITY INSTANT ADHESIVE known as 444(TM) TakPak® Instant Adhesi
---
LOCTITE 406 WICKING GRADE INSTANT ADHESIVE known as Loctite 406 500ML AU
---
Loctite 407
---
LOCTITE DSP 3214 TEMPORARY BONDING known as Loctite 3214 2L N/CH/JP
---
LOCTITE 480 INSTANT ADHESIVE known as 480 CA INSTANT ADHESIVE 20 G
---
LOCTITE AA 326 STRUCTURAL ADH known as 326 SPEEDBONDER 50ML EN/JP/CH
---
LOCTITE 406
---
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Prevent contact with eyes, skin and clothing. Do not breathe vapor and mist. Wash thoroughly after handling. Avoid contact with fabric or paper goods. Contact with these materials may cause rapid polymerization which can generate smoke and strong irritating vapors, and cause thermal burns.
Not available.
Wash thoroughly after handling.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Stable under recommended storage conditions.
Not available.
Rapid exothermic polymerization will occur in the presence of water, amines, alkalis and alcohols.
Spontaneous polymerization.
Water, amines, alkalis and alcohols.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- 3334
- Shipping Name
- Aviation regulated liquid, n.o.s. (Cyanoacrylate ester)
- Transport Class
- 9
- Packing Group
- III
Primary packs containing less than 500ml are unregulated by this mode of transport and may be shipped unrestricted.
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for LOCTITE 407 LOW VISCOSITY known as 407 INSTANT ADHESIVE IN JP 50?
The signal word is warning.
What is the physical form of LOCTITE 407 LOW VISCOSITY known as 407 INSTANT ADHESIVE IN JP 50?
LOCTITE 407 LOW VISCOSITY known as 407 INSTANT ADHESIVE IN JP 50 is a liquid with colourless color. It has irritating odor.
What are the hazard statements for LOCTITE 407 LOW VISCOSITY known as 407 INSTANT ADHESIVE IN JP 50?
This substance has 3 hazard statements:
- H335: MAY CAUSE RESPIRATORY IRRITATION
- COMBUSTIBLE LIQUID
- CAUSES EYE IRRITATION
What is the melting point of LOCTITE 407 LOW VISCOSITY known as 407 INSTANT ADHESIVE IN JP 50?
The melting point is Not available. and the boiling point is > 300 °F (> 148.9 °C) None.