NextSDS Logo
Safety Data Sheet EN

LOCTITE AA 5832 18KG

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report.

Get Free Audit
01

Identification

Product identifiers, regulatory numbers, and supplier information

Product Information

Product Name
LOCTITE AA 5832 18KG
Product Code
3053672

Regulatory Identifiers

CAS Number
N/A

Manufacturers & Suppliers

Henkel Corporation logo

Henkel Corporation

manufacturer

One Henkel Way, Rocky Hill, Connecticut 06067

+1 (860) 571-5100

www.henkelna.com

Emergency Contacts

CHEMTREC

1-703-527-3887

Poison Control Center

1-877-671-4608

Poison Control Center

1-303-592-1711

CHEMTREC

1-800-424-9300

02

Hazard Identification

GHS classification, signal word, pictograms, and hazard statements

Classified danger

Hazard Classifications

Flam. Liq. Cat. 4
Acute Tox. Cat. 4
Eye Dam. Cat. 1
Skin Sens. Cat. 1
STOT SE Cat. 2

GHS Pictograms

GHS05 - Corrosive

GHS05

GHS07 - Health hazard

GHS07

GHS08 - Serious health hazard

GHS08

Hazard Statements

H227 COMBUSTIBLE LIQUID
H302 HARMFUL IF SWALLOWED
H317 MAY CAUSE AN ALLERGIC SKIN REACTION
H318 CAUSES SERIOUS EYE DAMAGE
H371 MAY CAUSE DAMAGE TO ORGANS

Precautionary Statements

P210 Keep away from heat, sparks, open flames, hot surfaces - no smoking.
P260 Do not breathe vapors, mist, or spray.
P264 Wash affected area thoroughly after handling.
P270 Do not eat, drink or smoke when using this product.
P272 Contaminated work clothing should not be allowed out of the workplace.
P280 Wear protective gloves, clothing, eye and face protection.
P302 + P352 IF ON SKIN: Wash with plenty of water.
P305 + P351 + P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
P308 + P311 If exposed or concerned: Call a POISON CENTER/doctor/...
P333 + P313 If skin irritation or rash occurs: Get medical attention.
P362 + P364 Take off contaminated clothing and wash it before reuse.
P370 + P378 In case of fire: Use foam, dry chemical or carbon dioxide to extinguish.
P403 Store in a well-ventilated place.
P405 Store locked up.
P501 Dispose of contents and/or container according to Federal, State/Provincial and local governmental regulations.
IF SWALLOWED: Call a POISON CENTER or doctor/ physician if you feel unwell. Rinse mouth.

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report

Free Audit
03

Composition / Information on Ingredients

Chemical components, concentration ranges, and hazardous substance identification

Type mixture
Chemical Name CAS Number Concentration Hazardous
3,3,5 Trimethylcyclohexyl methacrylate 7779-31-9 10 - 30% Yes
N,N-Dimethylacrylamide 2680-03-7 10 - 30% Yes
Methacrylamide 79-39-0 1 - 5% Yes
1-Acetyl-2-phenylhydrazine 114-83-0 0.1 - 1% Yes
04

First Aid Measures

Emergency procedures for chemical exposure incidents

Inhalation

If not breathing, give artificial respiration. If breathing is difficult, oxygen should be administered by qualified personnel. Move to fresh air. If symptoms persist, seek medical advice.

Skin contact

Rinse with running water and soap. Remove contaminated clothing and shoes. Wash contaminated clothing before reuse. Thoroughly clean shoes before reuse. Discard any shoes or clothing items that cannot be decontaminated. Seek medical attention immediately.

Eye contact

Rinse immediately with plenty of water, also under the eyelids, for at least 15 minutes. Seek medical attention immediately.

Ingestion

Seek immediate medical attention. Do not induce vomiting. Never give anything by mouth to an unconscious person.

Immediate Medical Attention

Seek medical attention immediately.

05

Firefighting Measures

Extinguishing media, specific hazards, and firefighter protection

Suitable media

Use extinguishing measures appropriate to local circumstances and the surrounding environment. Water spray (fog), foam, dry chemical or carbon dioxide.

Unsuitable media

Not available.

Specific hazards

Uncontrolled polymerization may occur at high temperatures resulting in explosions or rupture of storage containers.

Instructions

In case of fire, keep containers cool with water spray.

Firefighter Protection

Wear self-contained breathing apparatus and full protective clothing, such as turn-out gear. Keep unnecessary personnel away.

06

Accidental Release Measures

Spill cleanup procedures, containment, and environmental protection

Emergency procedures

isolate the hazard area and deny entry to unnecessary and unprotected personnel.

Environmental

Do not allow product to enter sewer or waterways. Prevent further leakage or spillage if safe to do so.

Cleanup methods

Soak up with inert absorbent material (e.g. sand, silica gel, acid binder, universal binder, sawdust). Scrape up spilled material and place in a closed container for disposal.

Materials: inert absorbent material (e.g. sand, silica gel, acid binder, universal binder, sawdust)

Related Products

Similar products with comparable safety profiles

07

Handling and Storage

Safe handling precautions, storage conditions, and workplace requirements

Handling

Use only with adequate ventilation. Remove all sources of ignition. Prevent contact with eyes, skin and clothing. Do not breathe vapor and mist. Wash thoroughly after handling. Wear suitable protective clothing, safety glasses and gloves. Keep container closed. Do not taste or swallow. DO NOT heat or spray. When using, do not eat, drink or smoke.

Storage

Keep in a cool, well ventilated area away from heat, sparks and open flame. Keep container tightly closed until ready for use. Protect from direct sunlight.

Hygiene

Wash thoroughly after handling. When using, do not eat, drink or smoke.

Fire prevention

Remove all sources of ignition. Keep away from heat, sparks and open flame.

08

Exposure Controls / PPE

Occupational exposure limits, engineering controls, and protective equipment

Engineering

Provide adequate local exhaust ventilation to maintain worker exposure below exposure limits.

Hands

Use chemical resistant, impermeable clothing including gloves

Eyes

Safety goggles or safety glasses with side shields. Full face protection should be used if the potential for splashing or spraying of product exists.

Respiratory

Use NIOSH approved respirator if there is potential to exceed exposure limit(s).

Skin/Body

Use chemical resistant, impermeable clothing including gloves and either an apron or body suit to prevent skin contact.

09

Physical and Chemical Properties

Appearance, physical state, melting point, boiling point, and material characteristics

Explosive Limits
---
Vapor Pressure
4.5 hPa (20 °C (68°F)) Internal Henkel specification
Appearance
---
State Under Standard Conditions
---
Odor
Acrylate
Metal Corrosion
---
Physical State
Liquid
Upper Explosive Limit
Not available.
Voc Content
25 %
Solidification Point
---
Flammability
Combustible Liquid, but difficult to ignite
Solubility In Fat
---
Form
---
Odor Threshold
Not available.
Boiling Point
148 °C (298.4 °F) Internal Henkel specification
Ph
Not applicable, Product is non-soluble (in water).
Relative Density
---
Cloud Point
---
Colour Intensity
---
Auto Ignition Temperature
Not available.
Solubility
Not miscible Water
Solubility In Water
---
Dynamic Viscosity
5,000 mPa.s
Kinematic Viscosity
5 m2/s
Colour
Amber
Bulk Density
---
Flash Point
87.5 °C (189.5 °F) Flash Point in closed cup
Relative Evaporation Rate
---
Vapor Density
---
Physical State Data
liquid
Lower Explosive Limit
Not available.
Properties Status
---
Decomposition Temperature
148 °C
Crystallisation Point
---
Molecular Weight
---
Evaporation Rate
Not available.
Freezing Point
---
Melting Point
Not applicable, Product is a liquid
Softening Point
---
Partition Coefficient
Not available.
Density
1.08 at 20 °C (68°F)
10

Stability and Reactivity

Chemical stability, hazardous reactions, and incompatible materials

Stability

Stable under normal conditions of storage and use.

Reactivity

Not available.

Hazardous reactions

None under normal processing.

Avoid

Keep away from heat, ignition sources and incompatible materials. Protect from direct sunlight. UV light.

Incompatible

Oxidizing agents. Acids. Bases. Amines. Reducing agents. Free radical initiators. Inert gases. Reactive metals. Heavy metals. Oxygen scavengers.

Decomposition

Oxides of carbon. Oxides of nitrogen. Oxides of silicon. Irritating vapors.

12

Ecological Information

Environmental toxicity, biodegradation, and bioaccumulation data

The data for this section has not been processed yet.

13

Disposal Considerations

Waste treatment methods, disposal recommendations, and waste codes

The data for this section has not been processed yet.

14

Transport Information

UN numbers, shipping names, transport classes, and regulatory requirements

UN Number
NA 1993
Shipping Name
Combustible liquid, n.o.s. (N,N-Dimethylacrylamide)
Transport Class
Combustible Liquid
Packing Group
III
15

Regulatory Information

Chemical regulations, safety assessments, and compliance status

The data for this section has not been processed yet.

?

Frequently Asked Questions

Common questions about safety, handling, and properties

What is the hazard signal word for LOCTITE AA 5832 18KG?

The signal word is danger.

What is the physical form of LOCTITE AA 5832 18KG?

LOCTITE AA 5832 18KG is a liquid with amber color. It has acrylate odor.

What is the solubility of LOCTITE AA 5832 18KG?

Not miscible Water

What are the hazard statements for LOCTITE AA 5832 18KG?

This substance has 5 hazard statements:

  • H227: COMBUSTIBLE LIQUID
  • H302: HARMFUL IF SWALLOWED
  • H317: MAY CAUSE AN ALLERGIC SKIN REACTION
  • H318: CAUSES SERIOUS EYE DAMAGE
  • H371: MAY CAUSE DAMAGE TO ORGANS

What is the melting point of LOCTITE AA 5832 18KG?

The melting point is Not applicable, Product is a liquid and the boiling point is 148 °C (298.4 °F) Internal Henkel specification.