NextSDS Logo
Safety Data Sheet EN

LOCTITE PC 7516 B known as Nordbak Trowel Mix

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report.

Get Free Audit
01

Identification

Product identifiers, regulatory numbers, and supplier information

Product Information

Product Name
LOCTITE PC 7516 B known as Nordbak Trowel Mix
Product Code
39748_653356

Regulatory Identifiers

CAS Number
N/A

Identified Uses

Epoxy Hardener

Uses advised against

None identified

Manufacturers & Suppliers

Henkel Corporation logo

Henkel Corporation

manufacturer

One Henkel Way, Rocky Hill, Connecticut 06067

+1 (860) 571-5100

www.henkelna.com

Emergency Contacts

Poison Control Center

1-877-671-4608

Poison Control Center

1-303-592-1711

CHEMTREC

1-800-424-9300

CHEMTREC

1-703-527-3887

02

Hazard Identification

GHS classification, signal word, pictograms, and hazard statements

Classified danger

Hazard Classifications

Acute Tox. Cat. 4
Acute Tox. Cat. 3
Skin Corr. Cat. 1
Eye Dam. Cat. 1
Resp. Sens. Cat. 1
Skin Sens. Cat. 1
Carc. Cat. 2
Repr. Cat. 2

GHS Pictograms

GHS05 - Corrosive

GHS05

GHS06 - Acute toxicity

GHS06

GHS08 - Serious health hazard

GHS08

Hazard Statements

H302 HARMFUL IF SWALLOWED.
H314 CAUSES SEVERE SKIN BURNS AND EYE DAMAGE.
H317 MAY CAUSE AN ALLERGIC SKIN REACTION.
H331 TOXIC IF INHALED.
H334 MAY CAUSE ALLERGY OR ASTHMA SYMPTOMS OR BREATHING DIFFICULTIES IF INHALED.
H351 SUSPECTED OF CAUSING CANCER.
H361 SUSPECTED OF DAMAGING FERTILITY OR THE UNBORN CHILD.

Precautionary Statements

P201 Obtain special instructions before use.
P202 Do not handle until all safety precautions have been read and understood.
P260 Do not breathe dust.
P264 Wash affected area thoroughly after handling.
P270 Do not eat, drink or smoke when using this product.
P271 Use only outdoors or in a well-ventilated area.
P272 Contaminated work clothing should not be allowed out of the workplace.
P280 Wear protective gloves, clothing, eye and face protection.
P284 [In case of inadequate ventilation] wear respiratory protection.
P301 + P330 + P331 IF SWALLOWED: Rinse mouth. Do NOT induce vomiting.
P303 + P361 + P353 If on skin (or hair): Take off immediately all contaminated clothing.
P304 + P340 + P310 IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing. Immediately call a POISON CENTER or physician.
P305 + P351 + P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
P308 + P313 IF exposed or concerned: Get medical attention.
P333 + P313 If skin irritation or rash occurs: Get medical attention.
P342 + P311 If experiencing respiratory symptoms: Call a poison center or physician.
P362 + P364 Take off contaminated clothing and wash it before reuse.
P403 + P233 Store in a well-ventilated place. Keep container tightly closed.
P405 Store locked up.
P501 Dispose of contents and/or container according to Federal, State/Provincial and local governmental regulations.
IF SWALLOWED: Call a POISON CENTER or doctor/ physician if you feel unwell. Rinse mouth.

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report

Free Audit
03

Composition / Information on Ingredients

Chemical components, concentration ranges, and hazardous substance identification

Type mixture
Chemical Name CAS Number Concentration Hazardous
1,2-Ethanediamine, N-(2-aminoethyl)-, reaction products with bisphenol A diglycidyl ether homopolymer 68411-71-2 10 - 30% Yes
Calcium carbonate 471-34-1 30 - 60% Yes
Fatty acids, C18 unsaturated, dimers, polymers with tall oil fatty acids and triethylenetetramine 68082-29-1 10 - 30% Yes
Diethylenetriamine 111-40-0 5 - 10% Yes
3,6-diazaoctanethylenediamine 112-24-3 5 - 10% Yes
4-nonylphenol, branched 84852-15-3 1 - 5% Yes
Silica Filler 112926-00-8 5 - 10% Yes
Titanium dioxide 13463-67-7 1 - 5% Yes
Amines, polyethylenepoly-, triethylenetetramine fraction 90640-67-8 1 - 5% Yes
1,2-Ethanediamine, N1,N1-bis(2-aminoethyl)- 4097-89-6 1 - 5% Yes
Phenol, 2-nonyl-, branched 91672-41-2 0.1 - 1% Yes
2-(2-aminoethylamino)ethanol 111-41-1 0.1 - 1% Yes
4-Methylimidazole 822-36-6 0.1 - 1% Yes
N-Aminoethylpiperazine 140-31-8 0.1 - 1% Yes
04

First Aid Measures

Emergency procedures for chemical exposure incidents

Inhalation

Move to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give oxygen. Get medical attention.

Skin contact

Remove contaminated clothing and footwear. Immediately flush skin with plenty of water (using soap, if available). Get medical attention. Wash clothing before reuse. Thoroughly clean shoes before reuse.

Eye contact

Immediately flush eyes with plenty of water for at least 15 minutes. Get medical attention.

Ingestion

Rinse the mouth. Drink 1-2 glasses of water. DO NOT induce vomiting unless directed to do so by medical personnel. Never give anything by mouth to an unconscious person. Get medical attention.

Immediate Medical Attention

Get medical attention.

05

Firefighting Measures

Extinguishing media, specific hazards, and firefighter protection

Suitable media

Water spray (fog), foam, dry chemical or carbon dioxide.

Specific hazards

Burning produces obnoxious and toxic fumes. Use of water may result in the formation of very toxic aqueous solutions.

Instructions

Wear self-contained breathing apparatus and full protective clothing, such as turn-out gear.

Firefighter Protection

Wear self-contained breathing apparatus and full protective clothing, such as turn-out gear.

06

Accidental Release Measures

Spill cleanup procedures, containment, and environmental protection

Emergency procedures

Evacuate and ventilate spill area; dike spill to prevent entry into water system; wear full protective equipment during clean-up. Refer to Section 8 'Exposure Controls / Personal Protection' prior to clean up.

Environmental

Do not allow product to enter sewer or waterways.

Cleanup methods

Soak up with inert absorbent material (e.g. sand, silica gel, acid binder, universal binder, sawdust). Scrape up spilled material and place in a closed container for disposal.

Materials: inert absorbent material (e.g. sand, silica gel, acid binder, universal binder, sawdust)

Related Products

Similar products with comparable safety profiles

07

Handling and Storage

Safe handling precautions, storage conditions, and workplace requirements

Handling

Prevent contact with eyes, skin and clothing. Do not breathe vapor and mist. Wash thoroughly after handling. Use only with adequate ventilation. Keep container closed.

Storage

Store in original container until ready to use. Keep container tightly closed and in a cool, well-ventilated place away from incompatible materials. Keep away from heat, spark and flame.

Hygiene

Wash thoroughly after handling.

Fire prevention

Keep away from heat, spark and flame.

08

Exposure Controls / PPE

Occupational exposure limits, engineering controls, and protective equipment

09

Physical and Chemical Properties

Appearance, physical state, melting point, boiling point, and material characteristics

Physical State
Paste, Solid, Product is a solid by ASTM D4359-90
Physical State Data
solid
State Under Standard Conditions
---
Appearance
Dark, Blue, Gray / Grey
Colour
Dark, Blue, Gray / Grey
Colour Intensity
---
Form
---
Odor
Amine
Odor Threshold
Not available.
Ph
Not applicable
Melting Point
Not available.
Boiling Point
Not determined
Flash Point
> 93 °C (> 199.4 °F) Tagliabue closed cup
Freezing Point
---
Softening Point
---
Solidification Point
---
Cloud Point
---
Crystallisation Point
---
Relative Evaporation Rate
---
Evaporation Rate
---
Vapor Pressure
Not available.
Vapor Density
---
Relative Density
1.57
Bulk Density
---
Density
---
Flammability
Not applicable
Upper Explosive Limit
Not available.
Lower Explosive Limit
Not available.
Explosive Limits
---
Auto Ignition Temperature
Not available.
Decomposition Temperature
Not available.
Solubility
Slight Water
Partition Coefficient
Not available.
Solubility In Water
Slight
Solubility In Fat
---
Molecular Weight
---
Voc Content
< 1.0 %; < 10 g/l (value for resin and hardener together) (estimated)
Metal Corrosion
---
Dynamic Viscosity
Not available.
Kinematic Viscosity
Not available.
Properties Status
---
10

Stability and Reactivity

Chemical stability, hazardous reactions, and incompatible materials

Stability

Stable under normal conditions of storage and use.

Reactivity

Not available.

Hazardous reactions

None under normal processing.

Avoid

Keep away from heat, ignition sources and incompatible materials.

Incompatible

Acids. Oxidizing agents. Peroxides. Sodium hypochlorite. Amines. This product slowly corrodes copper, aluminum, zinc and galvanized surfaces. Nitrous acid and other nitrosating agents. CAUTION! N-nitrosamines (many of which are known to be potent carcinogens) may be formed when the product comes in contact with nitrous acid, nitrites or atmospheres with high nitrous oxide concentrations.

Decomposition

Upon decomposition, this product emits carbon monoxide, carbon dioxide and/or low molecular weight hydrocarbons. Oxides of nitrogen. Acids. Ammonia. Calcium oxide. Chlorine. Phenolics. Toxic fumes. Nitrosamines. Irritating vapors.

12

Ecological Information

Environmental toxicity, biodegradation, and bioaccumulation data

The data for this section has not been processed yet.

13

Disposal Considerations

Waste treatment methods, disposal recommendations, and waste codes

The data for this section has not been processed yet.

14

Transport Information

UN numbers, shipping names, transport classes, and regulatory requirements

UN Number
3259
Shipping Name
Amines, solid, corrosive, n.o.s. (Triethylenetetramine, Diethylenetriamine)
Transport Class
8
Packing Group
II
15

Regulatory Information

Chemical regulations, safety assessments, and compliance status

The data for this section has not been processed yet.

?

Frequently Asked Questions

Common questions about safety, handling, and properties

What is the hazard signal word for LOCTITE PC 7516 B known as Nordbak Trowel Mix?

The signal word is danger.

What is the physical form of LOCTITE PC 7516 B known as Nordbak Trowel Mix?

LOCTITE PC 7516 B known as Nordbak Trowel Mix is a paste, solid, product is a solid by astm d4359-90 appearing as dark, blue, gray / grey with dark, blue, gray / grey color. It has amine odor.

What is the solubility of LOCTITE PC 7516 B known as Nordbak Trowel Mix?

Slight Water

What is LOCTITE PC 7516 B known as Nordbak Trowel Mix used for?

Epoxy Hardener

What are the hazard statements for LOCTITE PC 7516 B known as Nordbak Trowel Mix?

This substance has 7 hazard statements:

  • H302: HARMFUL IF SWALLOWED.
  • H314: CAUSES SEVERE SKIN BURNS AND EYE DAMAGE.
  • H317: MAY CAUSE AN ALLERGIC SKIN REACTION.
  • H331: TOXIC IF INHALED.
  • H334: MAY CAUSE ALLERGY OR ASTHMA SYMPTOMS OR BREATHING DIFFICULTIES IF INHALED.
  • H351: SUSPECTED OF CAUSING CANCER.
  • H361: SUSPECTED OF DAMAGING FERTILITY OR THE UNBORN CHILD.

What is the melting point of LOCTITE PC 7516 B known as Nordbak Trowel Mix?

The melting point is Not available. and the boiling point is Not determined.