Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- TECHNOMELT PA 7804 known as HYSOL 7804 POLYSHOT 25 LB PA
- Product Code
- IDH number: 398484, Item number: 83330
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Hotmelt adhesive
Uses advised against
None identified
Manufacturers & Suppliers
Henkel Corporation
manufacturer
One Henkel Way, Rocky Hill, Connecticut 06067
+1 (860) 571-5100
www.henkelna.com
Emergency Contacts
Poison Control Center
1-877-671-4608
Poison Control Center
1-303-592-1711
CHEMTREC
1-800-424-9300
CHEMTREC
1-703-527-3887
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
GHS Pictograms
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
Notes
Exact percentages may vary or are trade secret. Concentration range is provided to assist users in providing appropriate protections.
First Aid Measures
Emergency procedures for chemical exposure incidents
Move to fresh air. If symptoms persist, seek medical advice.
Cool skin rapidly with cold water after contact with molten material. Cover affected areas with clean sheeting or gauze and seek immediate medical attention.
If eye contact occurs with molten material immediately cool with water. Do not remove adhesive. Seek medical attention.
Do not induce vomiting. Seek medical advice.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
water, carbon dioxide, foam, powder
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Use personal protection recommended in Section 8, isolate the hazard area and deny entry to unnecessary and unprotected personnel.
Do not allow material to contaminate ground water system.
Sweep up spilled material.
Related Products
Similar products with comparable safety profiles
TECHNOMELT PA 7811 PELLETS/1000 LBS.
---
TECHNOMELT 1942 YSHOT 35 LB CT
---
TECHNOMELT PA 7811
---
TECHNOMELT PA 3271 known as Loctite TPX3271 PELLETS 40LB EN
---
TECHNOMELT PA 673 OG BX-454KG
---
TECHNOMELT PA 2391 known as MACROMELT 2391 40LB
---
TECHNOMELT PA 2234 BG20KG
---
TECHNOMELT PUR 6358 SL 2KG
---
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Do not place wet or damp solid into melt tank. Follow suggested application temperature. Always be careful around molten material. Avoid skin contact with molten resins. Do not wear contact lenses. Avoid dust formation.
Keep cool in accordance with information on label and in Technical Data Sheets.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Use adequate ventilation to remove molten vapors or fumes.
Insulated gloves
Safety goggles or safety glasses with side shields. Full face protection should be used if the potential for splashing or spraying of product exists. Do not wear contact lenses.
Solid Resin: Dust safety masks are recommended when the potential for dust inhalation exists. Molten Resin: Use a NIOSH approved air-purifying respirator with an organic vapor cartridge.
long sleeved clothing are strongly recommended when working with molten adhesive.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Stable
Not available.
Will not occur.
Excessive heat.
Acids. Bases. Oxidizing agents.
Carbon dioxide, carbon monoxide and irritating and/or toxic gases and particulate may be generated by thermal decomposition or combustion.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for TECHNOMELT PA 7804 known as HYSOL 7804 POLYSHOT 25 LB PA?
The signal word is no signal word.
What is the physical form of TECHNOMELT PA 7804 known as HYSOL 7804 POLYSHOT 25 LB PA?
TECHNOMELT PA 7804 known as HYSOL 7804 POLYSHOT 25 LB PA is a solid with amber color. It has odourless / odorless odor.
What is the solubility of TECHNOMELT PA 7804 known as HYSOL 7804 POLYSHOT 25 LB PA?
Insoluble Water
What is TECHNOMELT PA 7804 known as HYSOL 7804 POLYSHOT 25 LB PA used for?
Hotmelt adhesive
What are the hazard statements for TECHNOMELT PA 7804 known as HYSOL 7804 POLYSHOT 25 LB PA?
This substance has 3 hazard statements:
- MOLTEN ADHESIVE MAY CAUSE SEVERE BURNS.
- VAPORS ABOVE MOLTEN ADHESIVE MAY CAUSE EYE, SKIN AND RESPIRATORY TRACT IRRITATION.
- STATIC CHARGES GENERATED BY EMPTYING PACKAGE IN OR NEAR FLAMMABLE VAPORS MAY CAUSE IGNITION.
What is the melting point of TECHNOMELT PA 7804 known as HYSOL 7804 POLYSHOT 25 LB PA?
The melting point is 137.7 °C (279.9 °F) (Softening Point) and the boiling point is > 220 °C (> 428°F).