Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- LOCTITE C 400 SN62 5C 0.32MM RF known as SN62 CRYSTAL 400 5C
- Product Form
- Solder Wire
- Product Code
- 291787
Regulatory Identifiers
- CAS Number
- N/A
Manufacturers & Suppliers
Henkel Corporation
manufacturer
One Henkel Way, Rocky Hill, Connecticut 06067
+1 (860) 571-5100
http://www.henkelna.com
Emergency Contacts
Poison Control Center
1-877-671-4608
Poison Control Center
1-303-592-1711
CHEMTREC
1-800-424-9300
CHEMTREC
1-703-527-3887
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS07
GHS08
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
First Aid Measures
Emergency procedures for chemical exposure incidents
Move to fresh air. If breathing is difficult, give oxygen. If not breathing, give artificial respiration. Get immediate medical attention.
Remove contaminated clothing and footwear. Immediately flush skin with plenty of water (using soap, if available). If symptoms develop and persist, get medical attention. Wash clothing before reuse.
Rinse immediately with plenty of water, also under the eyelids, for at least 15 minutes. Get medical attention.
Do not induce vomiting. Never give anything by mouth to an unconscious person. Get immediate medical attention.
Immediate Medical Attention
Get immediate medical attention.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Foam, dry chemical or carbon dioxide.
Wear a self-contained breathing apparatus with a full face piece operated in pressure-demand or other positive pressure mode.
Firefighter Protection
Wear a self-contained breathing apparatus with a full face piece operated in pressure-demand or other positive pressure mode.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Use personal protection recommended in Section 8, isolate the hazard area and deny entry to unnecessary and unprotected personnel.
Do not allow product to enter sewer or waterways.
Soak up with inert absorbent material (e.g. sand, silica gel, acid binder, universal binder, sawdust). Scrape up spilled material and place in a closed container for disposal.
Materials: inert absorbent material (e.g. sand, silica gel, acid binder, universal binder, sawdust)
Related Products
Similar products with comparable safety profiles
LOCTITE C 511 60EN 5C 0.7MM R known as 60EN CRYSTAL 511 5C
---
LOCTITE C 400 96SC 5C 0.5MM G
---
LOCTITE C 511 96SC 3C 0.23MM GN known as 96SC CRYSTAL 511 3C
---
LOCTITE CR 32 95AAGS88 C known as 95SN/5SB CR32 AGS88 250G/J
---
LOCTITE C 502 SN63 5C 0.38MM R known as 63/37 C502 5C 0.38MM 0.25KG AM
---
LOCTITE CR 32 95AAGS88 C known as 95A CR32 AGS88 250GJ - LN
---
LOCTITE C 502 SN63 3C 0.61MM S known as 63/37 C502 3C 0.61MM 0.5KG
---
LOCTITE C 502 SN63 3C 0.81MM S known as 63/37 C502 3C 0.81MM 0.5KG AM
---
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Wear suitable protective clothing, gloves and eye/face protection. Avoid contact with eyes, skin and clothing. Avoid skin contact with molten resins. Do not wear contact lenses.
Store in original container until ready to use. Keep in a cool, well ventilated area away from heat, sparks and open flame. Keep container tightly closed until ready for use. Store between 15 °C (59°F) and 30 °C (86°F).
Wash thoroughly after handling.
Keep in a cool, well ventilated area away from heat, sparks and open flame.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Stable under recommended storage conditions.
Not available.
Will not occur.
Solder alloy will react with concentrated nitric acid to produce toxic fumes of nitrogen oxides.
Oxidizing agents. Acids and bases.
Thermal decomposition can lead to release of irritating gases and vapors. Metal oxide fumes. Formaldehyde.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for LOCTITE C 400 SN62 5C 0.32MM RF known as SN62 CRYSTAL 400 5C?
The signal word is danger.
What is the physical form of LOCTITE C 400 SN62 5C 0.32MM RF known as SN62 CRYSTAL 400 5C?
LOCTITE C 400 SN62 5C 0.32MM RF known as SN62 CRYSTAL 400 5C is a solid with gray color.
What are the hazard statements for LOCTITE C 400 SN62 5C 0.32MM RF known as SN62 CRYSTAL 400 5C?
This substance has 4 hazard statements:
- H302 + H332: HARMFUL IF SWALLOWED OR IF INHALED.
- H336: MAY CAUSE DROWSINESS OR DIZZINESS.
- H360: MAY DAMAGE FERTILITY OR THE UNBORN CHILD.
- H372: CAUSES DAMAGE TO ORGANS THROUGH PROLONGED OR REPEATED EXPOSURE.
What is the melting point of LOCTITE C 400 SN62 5C 0.32MM RF known as SN62 CRYSTAL 400 5C?
The melting point is 179.0 °C (354.2 °F) (solder alloy) and the boiling point is Not available..