Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- TECHNOMELT AS 8707 known as Technomelt Q 80-8707 BX
- Product Form
- Hotmelt adhesive
- Product Code
- 1380974
Regulatory Identifiers
- CAS Number
- N/A
Manufacturers & Suppliers
Henkel Corporation
manufacturer
One Henkel Way, Rocky Hill, Connecticut 06067
+1 (860) 571-5100
http://www.henkelna.com
Emergency Contacts
Poison Control Center
1-877-671-4608
Poison Control Center
1-303-592-1711
CHEMTREC
1-800-424-9300
CHEMTREC
1-703-527-3887
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
GHS Pictograms
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Hydrocarbon Resin | --- | 30 - 60% | Yes |
| Copolymer | --- | 30 - 60% | Yes |
IDH number: 1380974 Product name: TECHNOMELT AS 8707 known as Technomelt Q 80-8707 BX
Notes
Exact percentage is a trade secret. Concentration range is provided to assist users in providing appropriate protections.
First Aid Measures
Emergency procedures for chemical exposure incidents
Move to fresh air in case of accidental inhalation of dust or fumes from overheating or combustion. If not breathing, give artificial respiration. If breathing is difficult, give oxygen.
Cover affected areas with clean sheeting or gauze and seek immediate medical attention. No attempt should be made to remove material from skin or to remove contaminated clothing as damaged skin can be easily torn. Cool melted product on skin with plenty of water. Do not remove solidified product.
Symptoms: Molten adhesive may cause severe burns.
If eye contact occurs with molten material immediately cool with water. Do not remove adhesive. Seek medical attention.
Ingestion of solid adhesive is not expected to be hazardous. If symptoms develop and persist, get medical attention.
Immediate Medical Attention
Seek immediate medical attention.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Use extinguishing measures appropriate to local circumstances and the surrounding environment. Water spray (fog), foam, dry chemical or carbon dioxide.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Use personal protection recommended in Section 8, isolate the hazard area and deny entry to unnecessary and unprotected personnel.
No special environmental precautions required. Do not allow material to contaminate ground water system.
Sweep up spilled material.
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Avoid skin contact with molten resins. Follow suggested application temperature. Do not place wet or damp solid into melt tank. Always be careful around molten material. Do not wear contact lenses.
Store between 0 °C (32°F) and 38 °C (100.4 °F). Store in sealed original container. Store in a dry place.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Ventilation hoods and fans required when working with organic solvents or in hot melt applications. Heat only in areas with appropriate exhaust ventilation.
Insulated gloves
Do not wear contact lenses. Safety goggles or safety glasses with side shields. Full face protection should be used if the potential for splashing or spraying of product exists.
Respirator with combination filter for vapor/particulate. In case of insufficient ventilation wear suitable respiratory equipment.
long sleeved clothing are strongly recommended when working with molten adhesive.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Stable
Not available.
Will not occur.
Prolonged heating at temperatures above 200 °C.
Avoid heating above 400°F.
Burning, including when heated by welding or cutting, will produce smoke, carbon monoxide and carbon dioxide.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for TECHNOMELT AS 8707 known as Technomelt Q 80-8707 BX?
The signal word is no signal word.
What is the physical form of TECHNOMELT AS 8707 known as Technomelt Q 80-8707 BX?
TECHNOMELT AS 8707 known as Technomelt Q 80-8707 BX is a solid with yellow color. It has resinous odor.
What are the hazard statements for TECHNOMELT AS 8707 known as Technomelt Q 80-8707 BX?
This substance has 3 hazard statements:
- MOLTEN ADHESIVE MAY CAUSE SEVERE BURNS.
- VAPORS ABOVE MOLTEN ADHESIVE MAY CAUSE EYE, SKIN AND RESPIRATORY TRACT IRRITATION.
- STATIC CHARGES GENERATED BY EMPTYING PACKAGE IN OR NEAR FLAMMABLE VAPORS MAY CAUSE IGNITION.
What is the melting point of TECHNOMELT AS 8707 known as Technomelt Q 80-8707 BX?
The melting point is 143 °C (289.4 °F) (Softening Point) and the boiling point is Not available..