Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- LOCTITE HC 3056 AERO PART A GAL
- Product Code
- AA9153018
- Synonyms
- TF 3056 PART A GALLON
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Adhesive for the Aerospace Industry
Uses advised against
None identified
Manufacturers & Suppliers
Henkel Corporation
manufacturer
One Henkel Way, Rocky Hill, Connecticut 06067
+1 (860) 571-5100
www.henkelna.com
Emergency Contacts
Poison Control Center
1-877-671-4608
Poison Control Center
1-303-592-1711
CHEMTREC
1-800-424-9300
CHEMTREC
1-703-527-3887
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS07
GHS08
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Epoxy resin | --- | 30 - 60% | Yes |
| Epoxy resin | --- | 5 - 10% | Yes |
| antimony trioxide | 1309-64-4 | 5 - 10% | Yes |
| Dimethyl methylphosphonate | 756-79-6 | 1 - 5% | Yes |
| 2,3-epoxypropyl o-tolyl ether | 2210-79-9 | 1 - 5% | Yes |
| Triphenyl phosphite | 101-02-0 | 1 - 5% | Yes |
| Dimethyl phosphonate | 868-85-9 | 0.1 - 1% | Yes |
Notes
* Exact percentages may vary or are trade secret. Concentration range is provided to assist users in providing appropriate protections.
First Aid Measures
Emergency procedures for chemical exposure incidents
If inhaled, immediately remove the affected person to fresh air.
Remove contaminated clothing and footwear. Immediately wash skin thoroughly with soap and water.
In case of contact with the eyes, rinse immediately with plenty of water for 15 minutes.
Do not induce vomiting.
Immediate Medical Attention
If symptoms develop and persist, get medical attention. Seek immediate medical attention (for eye contact). Get immediate medical attention (for ingestion).
Medical Treatment
Treat symptomatically and supportively.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Water spray (fog), foam, dry chemical or carbon dioxide.
Not available.
May liberate large quantities of dense, foul-smelling smoke which may contain unidentified toxic gasses.
Wear full protective clothing. Wear self-contained breathing apparatus.
Firefighter Protection
Wear full protective clothing. Wear self-contained breathing apparatus.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Use personal protection recommended in Section 8, isolate the hazard area and deny entry to unnecessary and unprotected personnel.
Prevent further leakage or spillage if safe to do so. Wear appropriate protective equipment and clothing during clean-up. Do not allow product to enter sewer or waterways.
Scrape up spilled material and place in a closed container for disposal.
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Follow curing schedule as recommended in product literature. Do not heat Part A at temperatures greater than 100 °C (212 °F). This material may self-react at higher temperatures and cause an exotherm. Empty containers retain product residue, so obey hazard warnings and handle empty containers as if they were full.
Store between 0 °C (32°F) and 5 °C (41°F). Keep container tightly closed and in a cool, well-ventilated place away from incompatible materials.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Stable at normal conditions.
Not available.
May occur.
Avoid mixing resin (Part A) and curing agent (Part B) unless you plan to use immediately. Do not heat mixed adhesive unless curing surfaces to be bonded. Failure to observe these precautions may result in excessive heat build-up causing an exotherm.
Keep away from strong oxidizing agents, strong Lewis or mineral acids.
Upon decomposition, this product emits carbon monoxide, carbon dioxide and/or low molecular weight hydrocarbons. Oxides of nitrogen.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- 3077
- Shipping Name
- RQ, Environmentally hazardous substance, solid, n.o.s.
- Transport Class
- 9
- Packing Group
- III
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What other names is LOCTITE HC 3056 AERO PART A GAL known by?
LOCTITE HC 3056 AERO PART A GAL is also known as: TF 3056 PART A GALLON
What is the hazard signal word for LOCTITE HC 3056 AERO PART A GAL?
The signal word is warning.
What is the physical form of LOCTITE HC 3056 AERO PART A GAL?
LOCTITE HC 3056 AERO PART A GAL is a solid with white color. It has epoxy odor.
What is the solubility of LOCTITE HC 3056 AERO PART A GAL?
Not soluble Water
What is LOCTITE HC 3056 AERO PART A GAL used for?
Adhesive for the Aerospace Industry
What are the hazard statements for LOCTITE HC 3056 AERO PART A GAL?
This substance has 5 hazard statements:
- H315: CAUSES SKIN IRRITATION.
- H317: MAY CAUSE AN ALLERGIC SKIN REACTION.
- H319: CAUSES SERIOUS EYE IRRITATION.
- H341: SUSPECTED OF CAUSING GENETIC DEFECTS.
- H351: SUSPECTED OF CAUSING CANCER.
What is the melting point of LOCTITE HC 3056 AERO PART A GAL?
The melting point is < -40 °C (< -40°F) and the boiling point is > 200 °C (> 392°F).