Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- TECHNOMELT DF 6360 ECO
- Product Code
- 2836304
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Hotmelt adhesivehotmelt, based on blockpolymer
Uses advised against
None identified
Manufacturers & Suppliers
Henkel Corporation
manufacturer
One Henkel Way, Rocky Hill, Connecticut 06067
+1 (860) 571-5100
http://www.henkelna.com
Emergency Contacts
Poison Control Center
1-877-671-4608
Poison Control Center
1-303-592-1711
CHEMTREC
1-800-424-9300
CHEMTREC
1-703-527-3887
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS07
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Styrenated terpene resin | --- | 30 - 60% | Yes |
| Isoprene-Styrene copolymer | 25038-32-8 | 10 - 30% | Yes |
| Talc | 14807-96-6 | 0.1 - 1% | Yes |
IDH number: 2836304 Page 1 of 5 Product name: TECHNOMELT DF 6360 ECO
First Aid Measures
Emergency procedures for chemical exposure incidents
Move to fresh air. If not breathing, give artificial respiration. If symptoms develop and persist, get medical attention.
Cool melted product on skin with plenty of water. Do not remove solidified product. No attempt should be made to remove material from skin or to remove contaminated clothing as damaged skin can be easily torn. Cover affected areas with clean sheeting or gauze and seek immediate medical attention.
Symptoms: Molten adhesive may cause severe burns.
If eye contact occurs with molten material immediately cool with water. Do not remove adhesive. Seek medical attention.
Ingestion of solid adhesive is not expected to be hazardous. If symptoms develop and persist, get medical attention.
Immediate Medical Attention
Seek immediate medical attention for skin burns or eye contact with molten material.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Use extinguishing measures appropriate to local circumstances and the surrounding environment. Dry chemical. Carbon dioxide.
Fire fighters should wear positive pressure self-contained breathing apparatus (SCBA). Wear full protective clothing.
Firefighter Protection
Fire fighters should wear positive pressure self-contained breathing apparatus (SCBA). Wear full protective clothing.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Use personal protection recommended in Section 8, isolate the hazard area and deny entry to unnecessary and unprotected personnel.
No special environmental precautions required. Do not allow material to contaminate ground water system.
Spilled material will solidify. Scrape up spilled material and place in a closed container for disposal.
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Always be careful around molten material. Avoid skin contact with molten resins. Follow suggested application temperature. Do not wear contact lenses. At elevated temperatures, irritating fumes may be emitted. Wash hands before breaks and immediately after handling the product.
store between 0.0 °C (32°F) and 38.0 °C (100.4 °F)
Wash hands before breaks and immediately after handling the product.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Stable
Not available.
Will not occur.
To avoid thermal decomposition, do not overheat. Avoid temperatures above 200°C (392°F).
Oxidizing agents.
Thermal decomposition can lead to release of irritating gases and vapors. carbon monoxide carbon dioxide
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for TECHNOMELT DF 6360 ECO?
The signal word is warning.
What is the physical form of TECHNOMELT DF 6360 ECO?
TECHNOMELT DF 6360 ECO is a solid with yellow color. It has hydrocarbon-like odor.
What is TECHNOMELT DF 6360 ECO used for?
Hotmelt adhesivehotmelt, based on blockpolymer
What are the hazard statements for TECHNOMELT DF 6360 ECO?
This substance has 2 hazard statements:
- H317: MAY CAUSE AN ALLERGIC SKIN REACTION.
- H319: CAUSES SERIOUS EYE IRRITATION.
What is the melting point of TECHNOMELT DF 6360 ECO?
The melting point is Not available. and the boiling point is > 230 °C (> 446°F) Boiling point.