NextSDS Logo
Safety Data Sheet EN

BONDERITE M-CR 600RTU

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report.

Get Free Audit
01

Identification

Product identifiers, regulatory numbers, and supplier information

Product Information

Product Name
BONDERITE M-CR 600RTU
Product Code
2707126

Regulatory Identifiers

CAS Number
N/A

Identified Uses

Conversion coating

Uses advised against

None identified

Manufacturers & Suppliers

Henkel Corporation logo

Henkel Corporation

manufacturer

One Henkel Way, Rocky Hill, Connecticut 06067

+1 (860) 571-5100

www.henkelna.com

Emergency Contacts

Poison Control Center

1-877-671-4608

Poison Control Center

1-303-592-1711

CHEMTREC

1-800-424-9300

CHEMTREC

1-703-527-3887

02

Hazard Identification

GHS classification, signal word, pictograms, and hazard statements

Classified danger

Hazard Classifications

Skin Irrit. Cat. 2
Eye Irrit. Cat. 2A
Resp. Sens. Cat. 1
Skin Sens. Cat. 1
Muta. Cat. 1B
Carc. Cat. 1A
Repr. Cat. 1B

GHS Pictograms

GHS08 - Serious health hazard

GHS08

Hazard Statements

H315 CAUSES SKIN IRRITATION.
H317 MAY CAUSE AN ALLERGIC SKIN REACTION.
H319 CAUSES SERIOUS EYE IRRITATION.
H334 MAY CAUSE ALLERGY OR ASTHMA SYMPTOMS OR BREATHING DIFFICULTIES IF INHALED.
H340 MAY CAUSE GENETIC DEFECTS.
H350 MAY CAUSE CANCER.
H360 MAY DAMAGE FERTILITY OR THE UNBORN CHILD.

Precautionary Statements

P201 Obtain special instructions before use.
P202 Do not handle until all safety precautions have been read and understood.
P261 Avoid breathing mist/vapours.
P264 Wash affected area thoroughly after handling.
P272 Contaminated work clothing should not be allowed out of the workplace.
P280 Wear protective gloves, clothing, eye and face protection.
P284 [In case of inadequate ventilation] wear respiratory protection.
P302 + P352 IF ON SKIN: Wash with plenty of water.
P304 + P340 IF INHALED: Remove person to fresh air and keep comfortable for breathing.
P305 + P351 + P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
P308 + P313 IF exposed or concerned: Get medical attention.
P333 + P313 If skin irritation or rash occurs: Get medical attention.
P337 + P313 If eye irritation persists: Get medical attention.
P342 + P311 If experiencing respiratory symptoms: Call a poison center or physician.
P362 + P364 Take off contaminated clothing and wash it before reuse.
P405 Store locked up.
P501 Dispose of contents and/or container according to Federal, State/Provincial and local governmental regulations.

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report

Free Audit
03

Composition / Information on Ingredients

Chemical components, concentration ranges, and hazardous substance identification

Type mixture
Chemical Name CAS Number Concentration Hazardous
Sodium chromate 7775-11-3 0.1 - 1% Yes
Dipotassium hexafluorozirconate 16923-95-8 0.1 - 1% Yes
Chromic acid 7738-94-5 0.1 - 1% Yes
04

First Aid Measures

Emergency procedures for chemical exposure incidents

Inhalation

Remove person immediately to fresh air. Seek medical attention if symptoms develop or persist. Administer oxygen or artificial respiration as needed. Do not use mouth-to-mouth method if victim ingested or inhaled the substance.

Symptoms: Delayed effects possible after inhalation.

Skin contact

Remove contaminated clothing and footwear. Immediately wash skin thoroughly with soap and water. If symptoms develop and persist, get medical attention. Launder contaminated clothing before reuse. Discard any shoes or clothing items that cannot be decontaminated.

Symptoms: Chromate scabs and skin ulcers.

Eye contact

Immediately flush affected eye with large amounts of gently flowing water or 0.9% sterile saline solution for at least 15 minutes. Hold eyelid wide open. Get immediate medical attention. Eye flushing should continue during transportation to a doctor.

Ingestion

Get immediate medical attention. Do not induce vomiting. If individual is conscious, wash out mouth with water. Provide a glass of water to dilute the material in the stomach.

Immediate Medical Attention

Get immediate medical attention for eye contact and ingestion.

Medical Treatment

Treat symptomatically and supportively. Larger exposures may need additional treatment.

05

Firefighting Measures

Extinguishing media, specific hazards, and firefighter protection

Suitable media

Use media appropriate for surrounding material. Water spray (fog), foam, dry chemical or carbon dioxide.

Unsuitable media

Not available.

Specific hazards

If evaporated to dryness, solid residue is an oxidizing agent and may cause spontaneous ignition of combustible materials. May liberate large quantities of dense, foul-smelling smoke which may contain unidentified toxic gasses.

Instructions

Wear full protective clothing. Wear self-contained breathing apparatus.

Firefighter Protection

Wear full protective clothing. Wear self-contained breathing apparatus.

06

Accidental Release Measures

Spill cleanup procedures, containment, and environmental protection

Emergency procedures

Use personal protection recommended in Section 8, isolate the hazard area and deny entry to unnecessary and unprotected personnel.

Environmental

Prevent further leakage or spillage if safe to do so. Wear appropriate protective equipment and clothing during clean-up. Do not allow product to enter sewer or waterways.

Cleanup methods

Absorb spill with inert material. Shovel material into appropriate container for disposal.

Materials: inert material

Related Products

Similar products with comparable safety profiles

07

Handling and Storage

Safe handling precautions, storage conditions, and workplace requirements

Handling

Avoid contact with eyes, skin and clothing. Wash thoroughly after handling. Avoid breathing mists or aerosols of this product. Use only with adequate ventilation. Launder work clothes frequently. Do not store or consume food, drink, or tobacco products in areas where they may become contaminated with this material. Do not take internally. For industrial use only.

Storage

Keep container tightly closed and in a cool, well-ventilated place away from incompatible materials. Protect from freezing.

Hygiene

Wash thoroughly after handling. Launder work clothes frequently. Do not store or consume food, drink, or tobacco products in areas where they may become contaminated with this material.

08

Exposure Controls / PPE

Occupational exposure limits, engineering controls, and protective equipment

09

Physical and Chemical Properties

Appearance, physical state, melting point, boiling point, and material characteristics

Lower Explosive Limit
Not applicable
Cloud Point
---
State Under Standard Conditions
---
Form
---
Relative Density
1.01 - 1.03
Colour Intensity
---
Appearance
---
Odor
Bland
Melting Point
Not applicable, Product is a liquid
Flash Point
> 93 °C (> 199.4 °F)
Colour
Orange
Solidification Point
---
Bulk Density
---
Crystallisation Point
---
Vapor Pressure
Not determined
Flammability
The product is not flammable.
Kinematic Viscosity
Not available.
Relative Evaporation Rate
---
Properties Status
---
Explosive Limits
---
Physical State
Liquid
Auto Ignition Temperature
Not applicable
Decomposition Temperature
Not available.
Density
---
Evaporation Rate
Not determined
Vapor Density
---
Upper Explosive Limit
Not applicable
Freezing Point
---
Solubility In Fat
---
Physical State Data
liquid
Softening Point
---
Solubility
Complete Water, Miscible Water
Molecular Weight
---
Solubility In Water
---
Dynamic Viscosity
Not available.
Odor Threshold
Not available.
Boiling Point
> 100 °C (> 212°F)
Voc Content
0 % (calculated)
Ph
< 2
Metal Corrosion
---
Partition Coefficient
Not available.
10

Stability and Reactivity

Chemical stability, hazardous reactions, and incompatible materials

Stability

Stable at normal conditions.

Reactivity

Not available.

Hazardous reactions

None under normal processing.

Avoid

None identified.

Incompatible

This product may react with strong reducing agents. Avoid contact with organic materials, oils, greases, and any oxidizable materials. Strong bases. Metals.

Decomposition

Upon decomposition, this product may yield oxides of nitrogen and ammonia, carbon dioxide, carbon monoxide and other low molecular weight hydrocarbons. Chromium oxide.

12

Ecological Information

Environmental toxicity, biodegradation, and bioaccumulation data

The data for this section has not been processed yet.

13

Disposal Considerations

Waste treatment methods, disposal recommendations, and waste codes

The data for this section has not been processed yet.

14

Transport Information

UN numbers, shipping names, transport classes, and regulatory requirements

UN Number
3082
Shipping Name
RQ, Environmentally hazardous substance, liquid, n.o.s.
Transport Class
9
Packing Group
III
15

Regulatory Information

Chemical regulations, safety assessments, and compliance status

The data for this section has not been processed yet.

?

Frequently Asked Questions

Common questions about safety, handling, and properties

What is the hazard signal word for BONDERITE M-CR 600RTU?

The signal word is danger.

What is the physical form of BONDERITE M-CR 600RTU?

BONDERITE M-CR 600RTU is a liquid with orange color. It has bland odor.

What is the solubility of BONDERITE M-CR 600RTU?

Complete Water, Miscible Water

What is BONDERITE M-CR 600RTU used for?

Conversion coating

What are the hazard statements for BONDERITE M-CR 600RTU?

This substance has 7 hazard statements:

  • H315: CAUSES SKIN IRRITATION.
  • H317: MAY CAUSE AN ALLERGIC SKIN REACTION.
  • H319: CAUSES SERIOUS EYE IRRITATION.
  • H334: MAY CAUSE ALLERGY OR ASTHMA SYMPTOMS OR BREATHING DIFFICULTIES IF INHALED.
  • H340: MAY CAUSE GENETIC DEFECTS.
  • H350: MAY CAUSE CANCER.
  • H360: MAY DAMAGE FERTILITY OR THE UNBORN CHILD.

What is the melting point of BONDERITE M-CR 600RTU?

The melting point is Not applicable, Product is a liquid and the boiling point is > 100 °C (> 212°F).