Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- Loctite(R) 3103 Adhesive Flexible UV Curing
- Product Code
- 231977
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Ultraviolet adhesive
Uses advised against
None identified
Manufacturers & Suppliers
Henkel Corporation
manufacturer
One Henkel Way, Rocky Hill, Connecticut 06067
+1 (860) 571-5100
http://www.henkelina.com
Emergency Contacts
Poison Control Center
1-877-671-4608
Poison Control Center
1-303-592-1711
CHEMTREC
1-800-424-9300
CHEMTREC
1-703-527-3887
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS07
GHS08
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Isobornyl acrylate | 5888-33-5 | 30 - 60% | Yes |
| 2-Hydroxyethyl methacrylate | 868-77-9 | 10 - 30% | Yes |
| Gamma-glycidoxypropyl trimethoxysilane | 2530-83-8 | 1 - 5% | Yes |
| diphenyl(2,4,6-trimethylbenzoyl)phosphine oxide | 75980-60-8 | 1 - 5% | Yes |
| Silica, amorphous, fumed, cryst.-free | 112945-52-5 | 1 - 5% | Yes |
| 2-Hydroxyethyl acrylate | 818-61-1 | 0.1 - 1% | Yes |
| 2-Propenoic acid, 2-methyl-, 2-(2-hydroxyethoxy)ethyl ester | 2351-43-1 | 0.1 - 1% | Yes |
* Exact percentages may vary or are trade secret. Concentration range is provided to assist users in providing appropriate protections.
First Aid Measures
Emergency procedures for chemical exposure incidents
Move to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give oxygen. Get medical attention.
Immediately flush skin with plenty of water (using soap, if available). Remove contaminated clothing and footwear. Get medical attention. Wash clothing before reuse.
Rinse immediately with plenty of water, also under the eyelids, for at least 15 minutes. Get medical attention.
DO NOT induce vomiting unless directed to do so by medical personnel. Never give anything by mouth to an unconscious person. Get medical attention.
Immediate Medical Attention
Get medical attention.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Water spray (fog), foam, dry chemical or carbon dioxide.
Not available.
Uncontrolled polymerization may occur at high temperatures resulting in explosions or rupture of storage containers.
Water may be unsuitable as an extinguishing media, but may be helpful in keeping adjacent containers cool.
Firefighter Protection
Wear self-contained breathing apparatus and full protective clothing, such as turn-out gear.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
isolate the hazard area and deny entry to unnecessary and unprotected personnel. Evacuate and ventilate spill area; dike spill to prevent entry into water system; wear full protective equipment during clean-up. Soak up with inert absorbent material. Scrape up as much material as possible. Store in a partly filled, closed container until disposal.
Do not allow product to enter sewer or waterways.
Soak up with inert absorbent material. Scrape up as much material as possible.
Materials: sand, silica gel, acid binder, universal binder, sawdust
Related Products
Similar products with comparable safety profiles
LOCTITE AA 3108 LIGHT CURING ADHESIVE known as LOCTITE® 3108™ LIGHT CURE ADHE
---
Loctite 4105 Instant Adhesive
---
LOCTITE DURO-TAK UV 4310
---
LOCTITE DURO-TAK UV 4194B
---
LOCTITE AA 3311 MED UV CURE known as Loctite 3311 Med.UV 1L
---
Loctite 330
---
LOCTITE AA 3311 RADITION CURING ADHESIVE known as 3311 Light Cure Adhesive Medic
---
Loctite 2701
---
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Prevent contact with eyes, skin and clothing. Do not breathe vapor and mist. Do not taste or swallow.
Store between 10 °C and 32 °C. Keep in a cool, well ventilated area away from heat, sparks and open flame. Keep container tightly closed until ready for use.
Wash thoroughly after handling.
Keep away from heat, sparks and open flame.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Provide adequate local exhaust ventilation to maintain worker exposure below exposure limits.
Use chemical resistant, impermeable clothing including gloves
Safety goggles or safety glasses with side shields. Full face protection should be used if the potential for splashing or spraying of product exists.
Use NIOSH approved respirator if there is potential to exceed exposure limit(s).
Use chemical resistant, impermeable clothing including gloves and either an apron or body suit to prevent skin contact.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Unstable at higher temperatures. Stable under recommended storage conditions.
Not available.
None under normal processing. Polymerization may occur at elevated temperature or in the presence of incompatible materials.
Heat, flames, sparks and other sources of ignition. Store away from incompatible materials. Ultraviolet radiation. Direct sunlight. Freezing conditions.
Strong oxidizing agents. Strong reducing agents. Strong acids. Strong bases. Free radical initiators. Water. Humid air. Heavy metals.
Oxides of carbon. Oxides of nitrogen. Oxides of silicon. Oxides of phosphorus. Irritating organic vapours. Dimethylamine. Formaldehyde. Hydrogen cyanide. Isocyanates. Amines.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- 3082
- Shipping Name
- Environmentally hazardous substance, liquid, n.o.s. (2,2-Dimethoxy-1,2-diphenylethan-1-one)
- Transport Class
- 9
- Packing Group
- III
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for Loctite(R) 3103 Adhesive Flexible UV Curing?
The signal word is warning.
What is the physical form of Loctite(R) 3103 Adhesive Flexible UV Curing?
Loctite(R) 3103 Adhesive Flexible UV Curing is a liquid with transparent, cloudy color. It has mild odor.
What is the solubility of Loctite(R) 3103 Adhesive Flexible UV Curing?
Slight Water
What is Loctite(R) 3103 Adhesive Flexible UV Curing used for?
Ultraviolet adhesive
What are the hazard statements for Loctite(R) 3103 Adhesive Flexible UV Curing?
This substance has 5 hazard statements:
- H227: COMBUSTIBLE LIQUID.
- H315: CAUSES SKIN IRRITATION.
- H317: MAY CAUSE AN ALLERGIC SKIN REACTION.
- H319: CAUSES SERIOUS EYE IRRITATION.
- H361: SUSPECTED OF DAMAGING FERTILITY OR THE UNBORN CHILD.
What is the melting point of Loctite(R) 3103 Adhesive Flexible UV Curing?
The melting point is Not applicable, Product is a liquid and the boiling point is > 93 °C (> 199.4 °F).