Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- LOCTITE DURO-TAK UV 4194B
- Product Code
- 2819409
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Pressure Sensitive Adhesives
Uses advised against
None identified
Manufacturers & Suppliers
Henkel Corporation
manufacturer
One Henkel Way, Rocky Hill, Connecticut 06067
+1 (860) 571-5100
www.henkelna.com
Emergency Contacts
Poison Control Center
1-877-671-4608
Poison Control Center
1-303-592-1711
CHEMTREC
1-800-424-9300
CHEMTREC
1-703-527-3887
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS02
GHS07
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
First Aid Measures
Emergency procedures for chemical exposure incidents
If not breathing, give artificial respiration. If breathing is difficult, oxygen should be administered by qualified personnel. Move to fresh air. If symptoms persist, seek medical advice.
Immediately flush skin with plenty of water (using soap, if available). Remove contaminated clothing and shoes. Get medical attention. Wash contaminated clothing before reuse. Thoroughly clean shoes before reuse. Discard any shoes or clothing items that cannot be decontaminated.
Check for and remove any contact lenses. Rinse immediately with plenty of water, also under the eyelids, for at least 15 minutes. Get medical attention.
If material is ingested, immediately contact a physician or poison control center. DO NOT induce vomiting unless directed to do so by medical personnel. If vomiting occurs, prevent aspiration by keeping the patient's head below the knees. Never give anything by mouth to an unconscious person.
Immediate Medical Attention
Get medical attention. Immediately contact a physician or poison control center.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Use extinguishing measures appropriate to local circumstances and the surrounding environment. Water spray (fog), foam, dry chemical or carbon dioxide.
Vapors may accumulate in low or confined areas, travel considerable distance to source of ignition, and flash back. Closed containers may rupture (due to build up of pressure) when exposed to extreme heat.
Isolate area. Keep unnecessary personnel away. In case of fire, keep containers cool with water spray.
Firefighter Protection
Wear self-contained breathing apparatus and full protective clothing, such as turn-out gear.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Use personal protection recommended in Section 8, isolate the hazard area and deny entry to unnecessary and unprotected personnel.
Prevent further leakage or spillage if safe to do so.
Transfer liquids to covered metal containers for recovery or disposal, or remove with inert absorbent.
Materials: inert absorbent
Related Products
Similar products with comparable safety profiles
LOCTITE DURO-TAK UV 4310
---
LOCTITE DURO-TAK UV 4194 ULTRA DR-F181KG
---
LOCTITE DURO-TAK UV 24110HNA RE
---
LOCTITE DURO-TAK UV 7020 ULTRA DR-F181KG
---
LOCTITE DURO-TAK UV 7050 ULTRA DR-F181KGKG
---
LOCTITE DURO-TAK 5542
---
LOCTITE DURO-TAK UV 4660 ULTRA PA16KG
---
LOCTITE DURO-TAK UV 5008NA PA-16 KG
---
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Keep container closed. Do not breathe gas/fumes/vapor/spray. Avoid contact with eyes, skin and clothing. Do not taste or swallow. 'Empty' containers retain product residue (liquid and/or vapor) and can be dangerous. Do not pressurize, cut, weld, braze, solder, drill, grind, or expose such containers to heat, flame, sparks, static electricity, or other sources of ignition; they may explode.
Keep container tightly closed and in a cool, well-ventilated place away from incompatible materials. Store in original container until ready to use.
Wash thoroughly after handling.
Do not handle or store near an open flame, heat or other sources of ignition. Keep away from heat, spark and flame.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Stable under normal conditions of storage and use.
This product may react with strong acids, bases and oxidizing agents.
None under normal processing.
Keep away from heat, ignition sources and incompatible materials. Take measures to prevent the build-up of electrostatic charges.
Strong acids, alkalies and oxidizing agents.
Irritating and toxic gases or fumes may be released during a fire. Oxides of carbon.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- 1133
- Shipping Name
- Adhesives
- Transport Class
- 3
- Packing Group
- II
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for LOCTITE DURO-TAK UV 4194B?
The signal word is danger.
What is the physical form of LOCTITE DURO-TAK UV 4194B?
LOCTITE DURO-TAK UV 4194B is a liquid appearing as clear with clear color. It has acrylic odor.
What is LOCTITE DURO-TAK UV 4194B used for?
Pressure Sensitive Adhesives
What are the hazard statements for LOCTITE DURO-TAK UV 4194B?
This substance has 5 hazard statements:
- H225: HIGHLY FLAMMABLE LIQUID AND VAPOUR.
- H315: CAUSES SKIN IRRITATION.
- H317: MAY CAUSE AN ALLERGIC SKIN REACTION.
- H319: CAUSES SERIOUS EYE IRRITATION.
- H336: MAY CAUSE DROWSINESS OR DIZZINESS.
What is the melting point of LOCTITE DURO-TAK UV 4194B?
The melting point is Not applicable, Product is a liquid and the boiling point is 78 - 85 °C (172.4 - 185°F)calculated.