NextSDS Logo
Safety Data Sheet EN

BONDERITE M-FE GS 755 known as BONDERITE M-FE GS 755 NR

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report.

Get Free Audit
01

Identification

Product identifiers, regulatory numbers, and supplier information

Product Information

Product Name
BONDERITE M-FE GS 755 known as BONDERITE M-FE GS 755 NR
Product Code
893060

Regulatory Identifiers

CAS Number
N/A

Identified Uses

Conversion coating

Uses advised against

None identified

Manufacturers & Suppliers

Henkel Corporation logo

Henkel Corporation

manufacturer

One Henkel Way, Rocky Hill, Connecticut 06067

+1 (860) 571-5100

http://www.henkelna.com

Emergency Contacts

Poison Control Center

1-877-671-4608

Poison Control Center

1-303-592-1711

CHEMTREC

1-800-424-9300

CHEMTREC

1-703-527-3887

02

Hazard Identification

GHS classification, signal word, pictograms, and hazard statements

Classified danger

Hazard Classifications

Skin Irrit. Cat. 2
Eye Dam. Cat. 1
Skin Sens. Cat. 1
Carc. Cat. 2
STOT RE Cat. 2

GHS Pictograms

GHS05 - Corrosive

GHS05

GHS07 - Health hazard

GHS07

GHS08 - Serious health hazard

GHS08

Hazard Statements

H315 CAUSES SKIN IRRITATION.
H317 MAY CAUSE AN ALLERGIC SKIN REACTION.
H318 CAUSES SERIOUS EYE DAMAGE.
H351 SUSPECTED OF CAUSING CANCER.
H373 MAY CAUSE DAMAGE TO ORGANS THROUGH PROLONGED OR REPEATED EXPOSURE.

Precautionary Statements

P201 Obtain special instructions before use.
P202 Do not handle until all safety precautions have been read and understood.
P260 Do not breathe vapors, mist, or spray.
P264 Wash affected area thoroughly after handling.
P272 Contaminated work clothing should not be allowed out of the workplace.
P280 Wear protective gloves, clothing, eye and face protection.
P302 + P352 IF ON SKIN: Wash with plenty of water.
P305 + P351 + P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
P308 + P313 IF exposed or concerned: Get medical attention.
P333 + P313 If skin irritation or rash occurs: Get medical attention.
P362 + P364 Take off contaminated clothing and wash it before reuse.
P405 Store locked up.
P501 Dispose of contents and/or container according to Federal, State/Provincial and local governmental regulations.

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report

Free Audit
03

Composition / Information on Ingredients

Chemical components, concentration ranges, and hazardous substance identification

Type mixture
Chemical Name CAS Number Concentration Hazardous
Benzoic acid 65-85-0 1 - 5% Yes
Phenol phosphate ester 39464-70-5 1 - 5% Yes
sodium 3-nitrobenzenesulphonate 127-68-4 1 - 5% Yes
Sodium xylene sulfonate 1300-72-7 1 - 5% Yes
Hydroxylamine sulfate 10039-54-0 1 - 5% Yes
Sodium fluoride 7681-49-4 0.1 - 1% Yes
Sodium borofluoride 13755-29-8 0.1 - 1% Yes

Notes

* Exact percentages may vary or are trade secret. Concentration range is provided to assist users in providing appropriate protections.

04

First Aid Measures

Emergency procedures for chemical exposure incidents

Inhalation

Remove person immediately to fresh air. Seek medical attention if symptoms develop or persist. If breathing is difficult, give oxygen. Trained personnel should administer 2.5% calcium gluconate through a nebulizer for 20 minutes.

Skin contact

Remove contaminated clothing and footwear while rinsing the affected area with large amounts of running water for at least 15 minutes. GET IMMEDIATE MEDICAL ATTENTION. If iced solution of 0.13% aqueous Benzalkonium Chloride (Zephiran) or 2.5% calcium gluconate gel is available, rinsing may be limited to 5 minutes, with the soak solution or gel applied as soon as the rinsing is stopped. If using calcium gluconate gel, it should be continuously re-applied and massaged into the affected area until pain has been relieved for at least 30 minutes. If Benzalkonium Chloride (Zephiran) or calcium gluconate gel is not available, rinsing must continue until medical treatment is provided.

Eye contact

Immediately flush affected eye with large amounts of gently flowing water or 0.9% sterile saline solution for at least 15 minutes. Hold eyelid wide open. Get immediate medical attention. Eye flushing should continue during transportation to a doctor.

Ingestion

Get immediate medical attention. DO NOT induce vomiting unless directed to do so by medical personnel. Attempt immediate administration of a fluoride binding substance: milk, chewable calcium carbonate tablets or 4-8 ounces (120-240 ml) of milk of magnesia or a liquid antacid. Avoid large amounts of liquid as it may induce vomiting. Never give anything by mouth to an unconscious person.

Immediate Medical Attention

Get immediate medical attention for all exposure routes.

Medical Treatment

Treatment of hypocalcemia associated with corrosive fluoride compounds exposure may be corrected by intravenous calcium gluconate or calcium chloride. Treatment of hypomagnesemia may be corrected by intravenous magnesium sulfate.

05

Firefighting Measures

Extinguishing media, specific hazards, and firefighter protection

Suitable media

Use media appropriate for surrounding material.

Specific hazards

Formation of toxic gases is possible during heating or in fires.

Instructions

Wear full protective clothing. Wear self-contained breathing apparatus.

Firefighter Protection

Wear full protective clothing. Wear self-contained breathing apparatus.

06

Accidental Release Measures

Spill cleanup procedures, containment, and environmental protection

Emergency procedures

Use personal protection recommended in Section 8, isolate the hazard area and deny entry to unnecessary and unprotected personnel.

Environmental

Prevent further leakage or spillage if safe to do so. Do not allow product to enter sewer or waterways.

Cleanup methods

Absorb spill with inert material. Shovel material into appropriate container for disposal.

Materials: inert material

Related Products

Similar products with comparable safety profiles

07

Handling and Storage

Safe handling precautions, storage conditions, and workplace requirements

Handling

Avoid contact with eyes, skin and clothing. Do not take internally. Wash thoroughly after handling. Wear protective equipment. Avoid breathing vapors or mists of this product. For industrial use only.

Storage

Keep container tightly closed and in a cool, well-ventilated place away from incompatible materials.

Hygiene

Wash thoroughly after handling.

08

Exposure Controls / PPE

Occupational exposure limits, engineering controls, and protective equipment

09

Physical and Chemical Properties

Appearance, physical state, melting point, boiling point, and material characteristics

Physical State Data
liquid
Softening Point
---
Freezing Point
---
Solubility
Moderate soluble
Physical State
Liquid
Solubility In Water
---
Solubility In Fat
---
Vapor Pressure
Not determined
Flammability
Not applicable
Molecular Weight
---
Density
---
Crystallisation Point
---
Dynamic Viscosity
Not available.
Properties Status
---
Odor Threshold
Not available.
Colour
Off white
Colour Intensity
---
Partition Coefficient
Not determined
Melting Point
15 °F (-9.4 °C)
Voc Content
Not applicable
Relative Evaporation Rate
---
Metal Corrosion
---
Explosive Limits
---
Auto Ignition Temperature
Not applicable
State Under Standard Conditions
---
Bulk Density
---
Evaporation Rate
Not applicable
Odor
Aromatic
Form
---
Vapor Density
---
Appearance
---
Boiling Point
> 100 °C (> 212°F)
Decomposition Temperature
Not available.
Ph
< 1
Kinematic Viscosity
Not available.
Solidification Point
---
Upper Explosive Limit
Not applicable
Flash Point
Not applicable
Relative Density
1.12 - 1.16
Cloud Point
---
Lower Explosive Limit
Not applicable
10

Stability and Reactivity

Chemical stability, hazardous reactions, and incompatible materials

Stability

Stable at normal conditions.

Reactivity

This product may react with strong alkalies.

Hazardous reactions

Will not occur.

Avoid

Store away from incompatible materials.

Incompatible

Keep away from alkalis.

Decomposition

Upon decomposition, this product emits oxides of sulfur, carbon monoxide, carbon dioxide and/or low molecular weight hydrocarbons. May liberate hydrogen fluoride.

12

Ecological Information

Environmental toxicity, biodegradation, and bioaccumulation data

The data for this section has not been processed yet.

13

Disposal Considerations

Waste treatment methods, disposal recommendations, and waste codes

The data for this section has not been processed yet.

14

Transport Information

UN numbers, shipping names, transport classes, and regulatory requirements

15

Regulatory Information

Chemical regulations, safety assessments, and compliance status

The data for this section has not been processed yet.

?

Frequently Asked Questions

Common questions about safety, handling, and properties

What is the hazard signal word for BONDERITE M-FE GS 755 known as BONDERITE M-FE GS 755 NR?

The signal word is danger.

What is the physical form of BONDERITE M-FE GS 755 known as BONDERITE M-FE GS 755 NR?

BONDERITE M-FE GS 755 known as BONDERITE M-FE GS 755 NR is a liquid with off white color. It has aromatic odor.

What is the solubility of BONDERITE M-FE GS 755 known as BONDERITE M-FE GS 755 NR?

Moderate soluble

What is BONDERITE M-FE GS 755 known as BONDERITE M-FE GS 755 NR used for?

Conversion coating

What are the hazard statements for BONDERITE M-FE GS 755 known as BONDERITE M-FE GS 755 NR?

This substance has 5 hazard statements:

  • H315: CAUSES SKIN IRRITATION.
  • H317: MAY CAUSE AN ALLERGIC SKIN REACTION.
  • H318: CAUSES SERIOUS EYE DAMAGE.
  • H351: SUSPECTED OF CAUSING CANCER.
  • H373: MAY CAUSE DAMAGE TO ORGANS THROUGH PROLONGED OR REPEATED EXPOSURE.

What is the melting point of BONDERITE M-FE GS 755 known as BONDERITE M-FE GS 755 NR?

The melting point is 15 °F (-9.4 °C) and the boiling point is > 100 °C (> 212°F).