Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- Insulfrax
- Product Form
- Substance
- Chemical Name
- AES wool (synthetic fibres, alkaline earth silicate)
Regulatory Identifiers
- CAS Number
- 436083-99-7 Check regulations →
- EC Number
- 650-016-00-2 Check regulations →
- REACH No.
- 01-2119457644-32-0002
Identified Uses
For industrial use within high temperature applications
Uses advised against
No additional information available
Manufacturers & Suppliers
INSULCON B.V.
manufacturer
Zilverhoek 4, 4651 SP STEENBERGEN
+31 (0)167-565750
http://www.insulcon.com
INSULCON N.V.
manufacturer
Belgium
+32 (0)3 711.02.78
INSULCON GMBH
manufacturer
Germany
+49 (0)2131 408548-0
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| AES wool (synthetic fibres, alkaline earth silicate) | 436083-99-7 | --- | No |
Notes
Note A: Without prejudice to Article 17(2), the name of the substance must appear on the label in the form of one of the designations given in Part 3. In Part 3, use is sometimes made of a general description such as ‘... compounds’ or ‘... salts’. In this case, the supplier is required to state on the label the correct name, due account being taken of section 1.1.1.4. Note Q: The classification as a carcinogen need not apply if it can be shown that the substance fulfils one of the following conditions: — a short term biopersistence test by inhalation has shown that the fibres longer than 20 µm have a weighted half-life less than 10 days; or — a short term biopersistence test by intratracheal instillation has shown that the fibres longer than 20 µm have a weighted half-life less than 40 days; or — an appropriate intra-peritoneal test has shown no evidence of excess carcinogenicity; or — absence of relevant pathogenicity or neoplastic changes in a suitable long term inhalation test. Note R: The classification as a carcinogen need not apply to fibres with a length weighted geometric mean diameter less two standard geometric errors greater than 6 µm
First Aid Measures
Emergency procedures for chemical exposure incidents
Move to fresh air.
Symptoms: Irritating to the respiratory system and mucous membranes. Mechanical irritation.
Gently wash with plenty of soap and water. Take off contaminated clothing and wash it before reuse.
Symptoms: May cause slight temporary irritation. mechanical irritation.
Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
Symptoms: May cause slight temporary irritation to ocular mucous membranes. mechanical irritation.
Rinse mouth. Do not induce vomiting.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
The product is not flammable. Use extinguishing media appropriate for surrounding fire. Foam. Dry powder. Carbon dioxide. Water spray.
Do not use a heavy water stream.
Non flammable.
Prevent firefighting water from entering the environment.
Firefighter Protection
Do not enter fire area without proper protective equipment, including respiratory protection.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Prohibit unauthorized persons. Ensure adequate ventilation. Manipulations are to be done only by qualified and authorised persons.
Prevent entry to sewers and public waters. Avoid sub-soil penetration.
Mechanically recover the product. Minimize generation of dust. High efficiency particulate air filter (HEPA filter).
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Obtain special instructions before use. Ensure good ventilation of the work station. Use personal protective equipment as required. Do not breathe dust. Avoid contact with skin and eyes. Clean contaminated areas thoroughly.
Product must only be kept in the original packaging. Store tightly closed in a dry and cool place.
Wash hands and other exposed areas with mild soap and water before eating, drinking or smoking and when leaving work.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Ensure good ventilation of the work station.
Leather protective gloves
Safety glasses with side shields. EN 166
Dust formation: dust mask. (FFP2)
Wear suitable protective clothing
Avoid release to the environment.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
The product is stable at normal handling and storage conditions.
Stable under normal conditions of use.
No dangerous reactions known.
No additional information available.
None.
Under normal conditions of storage and use, hazardous decomposition products should not be produced.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for Insulfrax?
The signal word is no signal word.
What is the physical form of Insulfrax?
Insulfrax is a solid appearing as fibres. with white. color. It has odourless. odor.
What is Insulfrax used for?
For industrial use within high temperature applications
What is the melting point of Insulfrax?
The melting point is >1300 °C and the boiling point is Not applicable.