Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- Foam 1
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Cleaner
Manufacturers & Suppliers
BOMA
distributor
Noorderlaan 131, B2030 Antwerpen
003232313389
http://www.boma.eu/
Emergency Contacts
Emergency Contact
+32 70 245 245
Emergency Contact
+31 30 274 88 88
Emergency Contact
+ 33 (0)1 45 42 59 59
Emergency Contact
(+352) 8002-5500
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS05
GHS07
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Phosphoric acid EC: 231-633-2 | 7664-38-2 | 30% | Yes |
| Hydroxyethylidene diphosphonic acid EC: 220-552-8 | 2809-21-4 | 5% | Yes |
| Dodecylbenzenesulphonic acid EC: 248-289-4 | 27176-87-0 | 5% | Yes |
| C8-10 D-glucoside EC: 500-220-1 | 68515-73-1 | 5% | Yes |
| Citric Acid EC: 201-069-1 | 77-92-9 | 5% | Yes |
| Sodium cumene sulfonate EC: 239-854-6 | 15763-76-5 | 5% | Yes |
First Aid Measures
Emergency procedures for chemical exposure incidents
let sit upright, fresh air, rest and take to hospital.
Symptoms: headache, dizziness, nausea, drowsiness, unconsciousness
remove contaminated clothing, rinse skin with plenty of water and immediately transport to hospital.
Symptoms: caustic, redness, pain, serious burns
first prolonged rinsing with water (contact lenses to be removed if this is easily done) then take to physician.
Symptoms: caustic, redness, bad looking, pain
rinse mouth, do not induce vomiting, take to hospital immediately.
Symptoms: caustic, lack of breath, vomiting, blisters on lips and tongue, burning pain in mouth and throat, gullet and stomach
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
CO2, foam, powder, sprayed water
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Do not walk into or touch spilled substances and avoid inhalation of fumes, smoke, dusts and vapours by staying up wind. Remove any contaminated clothing and used contaminated protective equipment and dispose of it safely.
do not allow to flow into sewers or open water.
store into suitable containers. If possible remove by using absorbent material.
Materials: absorbent material
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
handle with care to avoid spillage.
keep in a sealed container in a closed, frost-free, ventilated room.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
use with sufficient exhaust ventilation.
handling with Viton-gloves (EN 374). Breakthrough time: >480' Material thickness: 0,7 mm. Thoroughly check gloves before use. Take of the gloves properly without touching the outside with your bare hands. The manufacturer of the protective gloves has to be consulted about the suitability for a specific work station.
Tight-fitting safety goggles. Wear a face shield and protective suit in case of exceptional processing problems.
If necessary, use an air-purifying face mask in case of respiratory hazards. Use the ABEK type as protection against these troublesome levels.
impermeable clothing. The type of protective equipment depends on the concentration and amount of hazardous substances at the work station in question.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
extremely high or low temperatures.
stable under normal conditions.
protect from sunlight and do not expose to temperatures exceeding + 50°C.
oxidants, alkalines
doesn't decompose with normal use
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- 3264
- Shipping Name
- Corrosive liquid, acidic, inorganic, n.o.s. (mixture with Phosphoric acid)
- Transport Class
- 8
- Packing Group
- III
Hazard characteristics: Risk of burns. Risk to the aquatic environment and the sewerage system.
Hazard characteristics: Risk of burns. Risk to the aquatic environment and the sewerage system.
Hazard characteristics: Risk of burns. Risk to the aquatic environment and the sewerage system.
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for Foam 1?
The signal word is danger.
What is the physical form of Foam 1?
Foam 1 is a liquid appearing as liquid . It has characteristic odor.
What is Foam 1 used for?
Cleaner
What are the hazard statements for Foam 1?
This substance has 3 hazard statements:
- H290: May be corrosive to metals.
- H302: Harmful if swallowed.
- H314: Causes severe skin burns and eye damage.
What is the melting point of Foam 1?
The melting point is 0 °C and the boiling point is 100 °C.