Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- LOCTITE 542
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Threadlocker
Manufacturers & Suppliers
Henkel AG & Co. KGaA
manufacturer
Henkelstr. 67, 40589 Düsseldorf, Germany
+49 211 797 0
Emergency Contacts
Henkel information service
+49-(0)211-797-3350
around-the-clock
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS07
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
Anaerobic Sealant
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Cumene hydroperoxide EC: 201-254-7 | 80-15-9 | 1 - 3% | Yes |
| N,N-Diethyl-p-toluidine EC: 210-345-0 | 613-48-9 | 0.1 - 1% | Yes |
| N,N-dimethyl-o-toluidine EC: 210-199-8 | 609-72-3 | 0.1 - 1% | Yes |
| methyl methacrylate EC: 201-297-1 | 80-62-6 | 0.1 - 1% | Yes |
| 1,4-Naphthalenedione EC: 204-977-6 | 130-15-4 | 0.01 - 0.1% | Yes |
First Aid Measures
Emergency procedures for chemical exposure incidents
Move to fresh air. If symptoms persist, seek medical advice.
Symptoms: Irritation, coughing, shortness of breath, chest tightness.
Rinse with running water and soap. Obtain medical attention if irritation persists.
Symptoms: Prolonged or repeated contact may cause skin irritation.
Rinse immediately with plenty of running water (for 10 minutes), seek medical attention from a specialist.
Symptoms: Irritation, conjunctivitis.
Rinse mouth, drink 1-2 glasses of water, do not induce vomiting, consult a doctor.
Immediate Medical Attention
See section: Description of first aid measures
Medical Treatment
See section: Description of first aid measures
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Carbon dioxide, foam, powder
None known
In the event of a fire, carbon monoxide (CO) and carbon dioxide (CO2) can be released.
In case of fire, keep containers cool with water spray.
Firefighter Protection
Wear self-contained breathing apparatus and full protective clothing, such as turn-out gear.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Ensure adequate ventilation. Avoid contact with skin and eyes. Wear protective equipment.
wipe up with paper towel and place in container for disposal.
absorb onto inert absorbent material and place in sealed container for disposal.
Do not empty into drains / surface water / ground water.
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Avoid skin and eye contact. Prolonged or repeated skin contact should be avoided to minimise any risk of sensitisation.
Refer to Technical Data Sheet
Wash hands before work breaks and after finishing work. Do not eat, drink or smoke while working. Good industrial hygiene practices should be observed.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Ensure good ventilation/extraction.
Chemical-resistant protective gloves (EN 374). Suitable materials for short-term contact or splashes (recommended: at least protection index 2, corresponding to > 30 minutes permeation time as per EN 374): nitrile rubber (NBR; >= 0.4 mm thickness). Suitable materials for longer, direct contact (recommended: protection index 6, corresponding to > 480 minutes permeation time as per EN 374): nitrile rubber (NBR; >= 0.4 mm thickness). This information is based on literature references and on information provided by glove manufacturers, or is derived by analogy with similar substances. Please note that in practice the working life of chemical-resistant protective gloves may be considerably shorter than the permeation time determined in accordance with EN 374 as a result of the many influencing factors (e.g. temperature). If signs of wear and tear are noticed then the gloves should be replaced.
Safety glasses with sideshields or chemical safety goggles should be worn if there is a risk of splashing. Protective eye equipment should conform to EN166.
Use only in well-ventilated areas. An approved mask or respirator fitted with an organic vapour cartridge should be worn if the product is used in a poorly ventilated area. Filter type: A (EN 14387)
Wear suitable protective clothing. Protective clothing should conform to EN 14605 for liquid splashes or to EN 13982 for dusts.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Stable under recommended storage conditions.
Reaction with strong acids. Reacts with strong oxidants.
See section reactivity
See section reactivity.
Irritating organic vapours. Oxides of carbon. Sulphur oxides nitrogen oxides
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for LOCTITE 542?
The signal word is warning.
What is the physical form of LOCTITE 542?
LOCTITE 542 is a liquid appearing as liquid, brown with brown color. It has characteristic odor.
What is the solubility of LOCTITE 542?
No data available / Not applicable
What is LOCTITE 542 used for?
Threadlocker
What are the hazard statements for LOCTITE 542?
This substance has 3 hazard statements:
- H319: Causes serious eye irritation.
- H335: May cause respiratory irritation.
- H412: Harmful to aquatic life with long lasting effects.
What is the melting point of LOCTITE 542?
The melting point is No data available / Not applicable and the boiling point is > 149 °C (> 300.2 °F).