Masson trichrome Reagent C

Remove to open air. If the subject stops breathing, administer artificial respiration. Get medical advice/attention immediately.

Remove contaminated clothing. Rinse skin with a shower immediately. Get medical advice/attention immediately. Wash contaminated clothing before using it again.

Remove contact lenses, if present. Wash immediately with plenty of water for at least 15 minutes, opening the eyelids fully. If problem persists, seek medical advice.

Get medical advice/attention immediately. Do not induce vomiting. Do not administer anything not explicitly authorised by a doctor.

carbon dioxide and chemical powder. For product loss or leakage that has not caught fire, water spray can be used to disperse flammable vapours and protect those trying to stem the leak.

Do not use jets of water.

If large quantities of the product are involved in a fire, they can make it considerably worse. Do not breathe combustion products.

Water is not effective for putting out fires but can be used to cool containers exposed to flames to prevent explosions.

Block the leakage if there is no hazard.

The product must not penetrate into the sewer system or come into contact with surface water or ground water.

Absorb the remainder with inert absorbent material.

Materials: inert absorbent material

Keep away from heat, sparks and naked flames; do not smoke or use matches or lighters. Never use compressed air when handling. Open containers with caution as they may be pressurised. Avoid contact with eyes and skin. Do not breathe powders, vapours or mists.

Store in a well ventilated and dry place, far away from sources of heat, naked flames, sparks and other sources of ignition. Keep containers well sealed and clearly labelled. Avoid overheating and violent blows.

Do not eat, drink or smoke during use. Wash hands after use.

Keep away from heat, sparks and naked flames; do not smoke or use matches or lighters.

As the use of adequate technical equipment must always take priority over personal protective equipment, make sure that the workplace is well aired through effective local aspiration.

Protect hands with category III work gloves (see standard EN 374). The following should be considered when choosing work glove material: compatibility, degradation, failure time and permeability. The work gloves' resistance to chemical agents should be checked before use, as it can be unpredictable. The gloves' wear time depends on the duration and type of use.

Wear airtight protective goggles (see standard EN 166).

If the threshold value (e.g. TLV-TWA) is exceeded for the substance or one of the substances present in the product, wear a mask with a type AX filter, whose limit of use will be defined by the manufacturer (see standard EN 14387). In the presence of gases or vapours of various kinds and/or gases or vapours containing particulate (aerosol sprays, fumes, mists, etc.) combined filters are required. Respiratory protection devices must be used if the technical measures adopted are not suitable for restricting the worker's exposure to the threshold values considered. The protection provided by masks is in any case limited. If the substance considered is odourless or its olfactory threshold is higher than the corresponding TLV-TWA and in the case of an emergency, wear open-circuit compressed air breathing apparatus (in compliance with standard EN 137) or external air-intake breathing apparatus (in compliance with standard EN 138). For a correct choice of respiratory protection device, see standard EN 529.

Wear category I professional long-sleeved overalls and safety footwear (see Directive 89/686/EEC and standard EN ISO 20344). Wash body with soap and water after removing protective clothing. Consider the appropriateness of providing antistatic clothing in the case of working environments in which there is a risk of explosion.

The emissions generated by manufacturing processes, including those generated by ventilation equipment, should be checked to ensure compliance with environmental standards.

See previous paragraph.

The product can decompose and/or react violently.

ETHANOL: risk of explosion on contact with: alkaline metals, alkaline oxides, calcium hypochlorite, sulphur monofluoride, acetic anhydride (with acids), concentrated hydrogen peroxide, perchlorates, perchloric acid, perchloronitrile, mercury nitrate, nitric acid, silver and nitric acid, silver nitrate, silver nitrate and ammonia, strong oxidising agents, nitrogen dioxide. Can react dangerously with: bromoacetylene, chlorine acetylene, bromine trifluoride, chromium trioxide, chromyl chloride, oxiranes, fluorine, potassium tert-butoxide, lithium hydride, phosphorus trioxide, black platinum, zirconium (IV) chloride, zirconium (IV) iodide.

As the product decomposes even at ambient temperature, it must be stored and used at a controlled temperature. Avoid violent blows. ETHANOL: avoid exposure to sources of heat and naked flames.

Information not available.

Information not available.