Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- 4-Ethyltoluene
- Product Code
- 04943
- Chemical Name
- 4-Ethyltoluene
Regulatory Identifiers
- CAS Number
- 622-96-8 Check regulations →
Identified Uses
Laboratory chemicals, Manufacture of substances
Manufacturers & Suppliers
Merck Life Science S.A.S
manufacturer
80 Rue de Luzais, F-38297 SAINT QUENTIN FALLAVIER CEDEX
+33 (0)1 85 16 94 34
Emergency Contacts
CHEMTREC
+33 (0)9 75 18 14 07
I.N.R.S.
+33 (0)1 45 42 59 59
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS02
GHS08
Hazard Statements
Precautionary Statements
Still copying SDS data manually?Free
You don't have to. NextSDS reads this SDS and adds the information to your library automatically.
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| 4-Ethyltoluene EC: 210-761-2 | 622-96-8 | 100% | Yes |
First Aid Measures
Emergency procedures for chemical exposure incidents
After inhalation: fresh air.
Take off immediately all contaminated clothing. Rinse skin with water/ shower.
After eye contact: rinse out with plenty of water. Remove contact lenses.
After swallowing: caution if victim vomits. Keep airways free. Call a physician immediately.
Symptoms: Risk of aspiration! Pulmonary failure possible after aspiration of vomit.
Immediate Medical Attention
Call a physician immediately.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Carbon dioxide (CO2) Foam Dry powder
For this substance/mixture no limitations of extinguishing agents are given.
Carbon oxides. Combustible. Vapours are heavier than air and may spread along floors. Forms explosive mixtures with air at elevated temperatures. Development of hazardous combustion gases or vapours possible in the event of fire.
Remove container from danger zone and cool with water.
Firefighter Protection
In the event of fire, wear self-contained breathing apparatus.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Do not breathe vapours, aerosols. Avoid substance contact. Ensure adequate ventilation. Keep away from heat and sources of ignition. Evacuate the danger area, observe emergency procedures, consult an expert.
Do not let product enter drains. Risk of explosion.
Take up carefully with liquid-absorbent material. Clean up affected area.
Materials: liquid-absorbent material (e.g. Chemizorb®)
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Change contaminated clothing. Wash hands after working with substance. For precautions see section 2.2.
Keep container tightly closed in a dry and well-ventilated place. Keep away from heat and sources of ignition.
Change contaminated clothing. Wash hands after working with substance.
Keep away from open flames, hot surfaces and sources of ignition.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Full contact: Material: Viton®, Minimum layer thickness: 0,7 mm, Break through time: 480 min, Material tested: Vitoject® (KCL 890 / Aldrich Z677698, Size M). Splash contact: Material: Nitrile rubber, Minimum layer thickness: 0,4 mm, Break through time: 10 min, Material tested: Camatril® (KCL 730 / Aldrich Z677442, Size M). This recommendation applies only to the product stated in the safety data sheet, supplied by us and for the designated use. When dissolving in or mixing with other substances and under conditions deviating from those stated in EN 16523-1 please contact the supplier of CE-approved gloves (e.g. KCL GmbH, D-36124 Eichenzell, Internet: www.kcl.de).
Use equipment for eye protection tested and approved under appropriate government standards such as NIOSH (US) or EN 166(EU). Safety glasses
Recommended Filter type: Filter A (acc. to DIN 3181) for vapours of organic compounds. The entrepreneur has to ensure that maintenance, cleaning and testing of respiratory protective devices are carried out according to the instructions of the producer. These measures have to be properly documented.
Flame retardant antistatic protective clothing.
Do not let product enter drains. Risk of explosion.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
The product is chemically stable under standard ambient conditions (room temperature).
Vapour/air-mixtures are explosive at intense warming.
Risk of ignition or formation of inflammable gases or vapours with: Strong oxidizing agents
Heating.
rubber
In the event of fire: see section 5
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- 3295
- Shipping Name
- HYDROCARBONS, LIQUID, N.O.S.
- Transport Class
- 3
- Packing Group
- III
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for 4-Ethyltoluene?
The signal word is danger.
What is the physical form of 4-Ethyltoluene?
4-Ethyltoluene is a liquid with light yellow color. It has characteristic odor.
What is 4-Ethyltoluene used for?
Laboratory chemicals, Manufacture of substances
What are the hazard statements for 4-Ethyltoluene?
This substance has 2 hazard statements:
- H226: Flammable liquid and vapour.
- H304: May be fatal if swallowed and enters airways.
What is the melting point of 4-Ethyltoluene?
The melting point is Melting point: -62 °C and the boiling point is 162 °C - lit..