Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- HDS 400 CF
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Cutting oil
Manufacturers & Suppliers
Intercon Enterprises Inc.
distributor
6901 72 Street Unit 216, CDN Delta BC V4G 0A2
604 946-6066
http://www.intercon1978.com
Jokisch GmbH
manufacturer
Industriestraße 5, D-33813 Oerlinghausen
+49.5202.9734-0
Emergency Contacts
Emergency Contact
+ 1 202 464 2554
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS07
Hazard Statements
Precautionary Statements
Still copying SDS data manually?Free
You don't have to. NextSDS reads this SDS and adds the information to your library automatically.
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Distillates (petroleum), hydrotreated light paraffinic | 64742-55-8 | 18.9% | Yes |
| Benzenesulfonic acid, di-C10-14-alkyl derivs., calcium salts | 1471316-72-9 | 0.2589% | Yes |
First Aid Measures
Emergency procedures for chemical exposure incidents
Move victim to fresh air. Put victim at rest and keep warm.
Remove contaminated, saturated clothing immediately. After contact with skin, wash immediately with plenty of water and soap. Seek medical attention if problems persist.
In case of contact with eyes, rinse immediately with plenty of flowing water for 10 to 15 minutes holding eyelids apart. Consult an ophthalmologist.
Do NOT induce vomiting. In case of swallowing, keep the patient at rest and contact a doctor.
Immediate Medical Attention
Seek medical attention if problems persist.
Medical Treatment
Treat symptomatically
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Water fog. Carbon dioxide.
High power water jet.
In case of fire may be liberated: Carbon dioxide (CO2). Carbon monoxide
Do not inhale explosion and combustion gases.
Firefighter Protection
Wear a self-contained breathing apparatus and chemical protective clothing.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Self-protection of the first aider Remove affected person from the danger area and lay down. Do not leave affected person unattended. Remove all sources of ignition.
Large quantities remove mechanically
Do not allow to enter into surface water or drains. Prevent spread over a wide area (e.g. by containment or oil barriers). Treat the recovered material as prescribed in the section on waste disposal.
Clean contaminated articles and floor according to the environmental legislation. Clean with detergents. Avoid solvent cleaners.
Materials: detergents
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Avoid oil mist. Use only in well-ventilated areas. Direct contact with skins avoid. When using do not eat, drink or smoke. High slip hazard because of leaking or spilled product.
Keep the packing dry and well sealed to prevent contamination and absorption of humidity. Protect from sunlight. Store in a well-ventilated place.
When using do not eat, drink or smoke. Use personal protection equipment as per Directive 89/686/EEC.
Prevent access by unauthorised personnel.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
If local exhaust ventilation is not possible or not sufficient, the entire working area should be ventilated by technical means.
Gloves of appropriate material (i.e. nitrilic rubber, specification: penetration time: level 6, >480 min., thickness 0,9-1 mm; CE-certified acc. EN 374 cat III)
Use glasses or face shield if there is a risk of splashing. EN 166
If technical exhaust or ventilation measures are not possible or insufficient, respiratory protection must be worn.
Chemical resistant safety shoes. Take off immediately all contaminated clothing.
Do not allow to enter into surface water or drains.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
The product is chemically stable under recommended conditions of storage, use and temperature.
No hazardous reaction when handled and stored according to provisions.
acid
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
Ecotoxicity
Persistence and degradability
Bioaccumulative potential
Mobility in soil
Results of PBT and vPvB assessment
Endocrine disrupting properties
Other adverse effects
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
Do not allow to enter into surface water or drains. Dispose of contents/container to an appropriate recycling or disposal facility. Waste disposal according to directive 2008/98/EC, covering waste and dangerous waste.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for HDS 400 CF?
The signal word is warning.
What is the physical form of HDS 400 CF?
HDS 400 CF is a liquid with amber coloured color. It has characteristic odor.
What is HDS 400 CF used for?
Cutting oil
What are the hazard statements for HDS 400 CF?
This substance has 1 hazard statement:
- H317: May cause an allergic skin reaction