2-Propanol

Remove to fresh air. If not breathing, give artificial respiration.

Symptoms: Difficulty in breathing. Inhalation of high vapor concentrations may cause symptoms like headache, dizziness, tiredness, nausea and vomiting.

Wash off immediately with plenty of water for at least 15 minutes.

Rinse immediately with plenty of water, also under the eyelids, for at least 15 minutes.

Do NOT induce vomiting.

CO₂, dry chemical, dry sand, alcohol-resistant foam. Water mist may be used to cool closed containers.

Do not use water jetstream. Do not use a solid water stream as it may scatter and spread fire.

Flammable. Risk of ignition. Vapors may form explosive mixtures with air. Vapors may travel to source of ignition and flash back. Containers may explode when heated.

Use personal protective equipment as required. Avoid contact with skin, eyes or clothing.

Should not be released into the environment. See Section 12 for additional Ecological Information.

Soak up with inert absorbent material.

Materials: inert absorbent material

Wear personal protective equipment/face protection. Keep away from open flames, hot surfaces and sources of ignition. Use spark-proof tools and explosion-proof equipment. Use only non-sparking tools. Take precautionary measures against static discharges. Do not get in eyes, on skin, or on clothing. Do not breathe mist/vapors/spray. To avoid ignition of vapors by static electricity discharge, all metal parts of the equipment must be grounded.

Keep container tightly closed in a dry and well-ventilated place.

Handle in accordance with good industrial hygiene and safety practice. Keep away from food, drink and animal feeding stuffs. Do not eat, drink or smoke when using this product. Remove and wash contaminated clothing and gloves, including the inside, before re-use. Wash hands before breaks and after work.

Keep away from open flames, hot surfaces and sources of ignition.

Ensure that eyewash stations and safety showers are close to the workstation location. Use explosion-proof electrical/ventilating/lighting equipment. Ensure adequate ventilation, especially in confined areas. Wherever possible, engineering control measures such as the isolation or enclosure of the process, the introduction of process or equipment changes to minimise release or contact, and the use of properly designed ventilation systems, should be adopted to control hazardous materials at source

Protective gloves. Butyl rubber (>480 minutes, 0.5 mm, EN 374, Permeation rate < 0.9 μg/cm2/min); Nitrile rubber (>360 - 480 minutes, 0.35 - 0.55 mm, As tested under EN374-3); Viton (R) (>480 minutes, 0.4 mm); Neoprene (< 40 minutes, 0.7 mm). Ensure gloves are suitable for the task: Chemical compatibility, Dexterity, Operational conditions, User susceptibility, e.g. sensitisation effects, also take into consideration the specific local conditions under which the product is used, such as the danger of cuts, abrasion. Remove gloves with care avoiding skin contamination.

Goggles (European standard - EN 166)

When workers are facing concentrations above the exposure limit they must use appropriate certified respirators. To protect the wearer, respiratory protective equipment must be the correct fit and be used and maintained properly. Large scale/emergency use: Use a NIOSH/MSHA or European Standard EN 136 approved respirator if exposure limits are exceeded or if irritation or other symptoms are experienced. Recommended Filter type: Organic gases and vapours filter Type A Brown conforming to EN14387. Small scale/Laboratory use: Use a NIOSH/MSHA or European Standard EN 149:2001 approved respirator if exposure limits are exceeded or if irritation or other symptoms are experienced. Recommended half mask:- Valve filtering: EN405; Half mask: EN140; plus filter, EN 141 When RPE is used a face piece Fit Test should be conducted

Wear appropriate protective gloves and clothing to prevent skin exposure. Inspect gloves before use. Please observe the instructions regarding permeability and breakthrough time which are provided by the supplier of the gloves.

No information available.

Stable under normal conditions.

None known, based on information available

Hazardous polymerization does not occur. None under normal processing.

Heat, flames and sparks. Keep away from open flames, hot surfaces and sources of ignition.

Strong oxidizing agents. Acids. Halogens. Acid anhydrides.

Carbon monoxide (CO). Carbon dioxide (CO₂). peroxides.

Dispose of in accordance with the European Directives on waste and hazardous waste. Dispose of in accordance with local regulations.

Waste is classified as hazardous. Dispose of in accordance with the European Directives on waste and hazardous waste.