Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- Ethylenediaminetetraacetic acid dipotassium salt dihydrate
- Product Code
- ED2P
Regulatory Identifiers
- CAS Number
- 25102-12-9 Check regulations →
Identified Uses
Laboratory chemicals, Synthesis of substances
Uses advised against
The product is being supplied under the TSCA R&D Exemption (40 CFR Section 720.36). It is the recipient's responsibility to comply with the requirements of the R&D exemption. The product may not be used for a non-exempt commercial purpose under TSCA unless appropriate consent is granted in writing by MilliporeSigma.
Manufacturers & Suppliers
Sigma-Aldrich Inc.
manufacturer
3050 SPRUCE ST, ST. LOUIS MO 63103, UNITED STATES
+1 314 771-5765
Emergency Contacts
CHEMTREC
800-424-9300
24 Hours/day; 7 Days/week
CHEMTREC
+1-703-527-3887
24 Hours/day; 7 Days/week
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS07
Hazard Statements
Precautionary Statements
Still copying SDS data manually?Free
You don't have to. NextSDS reads this SDS and adds the information to your library automatically.
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Ethylenediamine-N,N,N',N'-tetraacetic acid dipotassium salt, dihydrate EC: 217-895-0 | 25102-12-9 | 100% | Yes |
First Aid Measures
Emergency procedures for chemical exposure incidents
fresh air. If breathing stops: mouth-to-mouth breathing or artificial respiration. Oxygen if necessary. Immediately call in physician.
Take off immediately all contaminated clothing. Rinse skin with water/ shower.
rinse out with plenty of water. Remove contact lenses.
make victim drink water (two glasses at most). Consult doctor if feeling unwell.
Immediate Medical Attention
Immediately call in physician.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Water Foam Carbon dioxide (CO2) Dry powder
For this substance/mixture no limitations of extinguishing agents are given.
Combustible. Development of hazardous combustion gases or vapours possible in the event of fire.
Suppress (knock down) gases/vapors/mists with a water spray jet.
Firefighter Protection
In the event of fire, wear self-contained breathing apparatus.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Avoid inhalation of dusts. Avoid substance contact. Ensure adequate ventilation. Evacuate the danger area, observe emergency procedures, consult an expert.
Do not let product enter drains.
Take up dry. Clean up affected area.
Related Products
Similar products with comparable safety profiles
Ethylenediaminetetraacetic acid dipotassium salt dihydrate
CAS: 25102-12-9
Ethylenediaminetetraacetic acid, dipotassium salt dehydrate
CAS: 25102-12-9
Ethylenediaminetetraacetic acid disodium salt dihydrate
CAS: 6381-92-6
Ethylenediaminetetraacetic acid disodium salt dihydrate
CAS: 6381-92-6
Ethylenediaminetetraacetic acid disodium salt dihydrate
CAS: 6381-92-6
Ethylenediaminetetraacetic acid disodium salt dihydrate
CAS: 6381-92-6
Ethylenediaminetetraacetic acid, disodium salt dihydrate
CAS: 6381-92-6
Ethylenediaminetetraacetic acid disodium salt solution
UFI: M822-N6KG-A99H-N19E
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Work under hood. Do not inhale substance/mixture.
Tightly closed. Dry.
Change contaminated clothing. Preventive skin protection recommended. Wash hands after working with substance.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Full contact: Material: Nitrile rubber, Minimum layer thickness: 0.11 mm, Break through time: 480 min, Material tested: KCL 741 Dermatril® L. Splash contact: Material: Nitrile rubber, Minimum layer thickness: 0.11 mm, Break through time: 480 min, Material tested: KCL 741 Dermatril® L. This recommendation applies only to the product stated in the safety data sheet, supplied by us and for the designated use. When dissolving in or mixing with other substances and under conditions deviating from those stated in EN 16523-1 please contact the supplier of CE-approved gloves (e.g. KCL GmbH, D-36124 Eichenzell, Internet: www.kcl.de).
Use equipment for eye protection tested and approved under appropriate government standards such as NIOSH (US) or EN 166(EU). Safety glasses
Recommended Filter type: Filter type P2. Required when dusts are generated. The entrepreneur has to ensure that maintenance, cleaning and testing of respiratory protective devices are carried out according to the instructions of the producer. These measures have to be properly documented. Our recommendations on filtering respiratory protection are based on the following standards: DIN EN 143, DIN 14387 and other accompanying standards relating to the used respiratory protection system.
protective clothing
Do not let product enter drains.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
The product is chemically stable under standard ambient conditions (room temperature).
The following applies in general to flammable organic substances and mixtures: in correspondingly fine distribution, when whirled up a dust explosion potential may generally be assumed.
Caution! In contact with nitrites, nitrates, nitrous acid possible liberation of nitrosamines! Violent reactions possible with: Strong oxidizing agents
no information available
nitrites, nitrates, nitrous acid, strong oxidizing agents
nitrosamines
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
12.1 Toxicity
12.2 Persistence and degradability
12.3 Bioaccumulative potential
12.4 Mobility in soil
12.5 Results of PBT and vPvB assessment
12.6 Endocrine disrupting properties
12.7 Other adverse effects
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
Waste material must be disposed of in accordance with the national and local regulations.
Leave chemicals in original containers. No mixing with other waste.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for Ethylenediaminetetraacetic acid dipotassium salt dihydrate?
The signal word is warning.
What is the physical form of Ethylenediaminetetraacetic acid dipotassium salt dihydrate?
Ethylenediaminetetraacetic acid dipotassium salt dihydrate is a powder with white color. It has no data available odor.
What is Ethylenediaminetetraacetic acid dipotassium salt dihydrate used for?
Laboratory chemicals, Synthesis of substances
What are the hazard statements for Ethylenediaminetetraacetic acid dipotassium salt dihydrate?
This substance has 1 hazard statement:
- H332: Harmful if inhaled.
What is the melting point of Ethylenediaminetetraacetic acid dipotassium salt dihydrate?
The melting point is Melting point/range: 255 - 280 °C (491 - 536 °F) - dec. and the boiling point is No data available.