Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- CMP Strukturspray transparent
- Product Code
- 174452
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Lacquer
Uses advised against
No further relevant information available.
Manufacturers & Suppliers
MOTIP DUPLI GmbH
manufacturer
Kurt Vogelsang Strasse 6, D-74855 Haßmersheim
+49/6266/75-0
Emergency Contacts
Emergency Contact
+49 6266-75-310
Mo - Th 08:00 am - 04:00 pm, Fr 08:00 am - 00:30 pm
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS02
GHS07
GHS08
Hazard Statements
Precautionary Statements
Still copying SDS data manually?Free
You don't have to. NextSDS reads this SDS and adds the information to your library automatically.
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| acetone EC: 200-662-2 | 67-64-1 | 25 - 50% | Yes |
| xylene EC: 905-588-0 | --- | 12.5 - 20% | Yes |
| propane EC: 200-827-9 | 74-98-6 | 12.5 - 20% | Yes |
| butane EC: 203-448-7 | 106-97-8 | 10 - 12.5% | Yes |
| n-butyl acetate EC: 204-658-1 | 123-86-4 | 5 - 10% | Yes |
| 2-methoxy-1-methylethyl acetate EC: 203-603-9 | 108-65-6 | 2.5 - 5% | Yes |
| isobutane EC: 200-857-2 | 75-28-5 | 2.5 - 5% | Yes |
The content of Benzene (EINECS-Nr. 200-753-7) in the ingredients is less than 0,1% (Note P Annex 1A 1272/2008 EU), so the classification as carcinogen need not to apply. xylene: Contains ethylbenzene CAS 100-41-4
First Aid Measures
Emergency procedures for chemical exposure incidents
In case of unconsciousness place patient stably in side position for transportation.
Immediately wash with water and soap and rinse thoroughly.
Rinse opened eye for several minutes under running water. If symptoms persist, consult a doctor.
Drink plenty of water and provide fresh air. Call for a doctor immediately.
Immediate Medical Attention
Call for a doctor immediately.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
CO2, powder or water spray. Fight larger fires with water spray or alcohol resistant foam. Use fire extinguishing methods suitable to surrounding conditions.
During heating or in case of fire poisonous gases are produced.
Firefighter Protection
Mouth respiratory protective device.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Mount respiratory protective device. Wear protective equipment. Keep unprotected persons away.
Do not allow to enter sewers/ surface or ground water.
Related Products
Similar products with comparable safety profiles
CM Kunststoff-Haftvermittler farblos 150ml
---
DUPLI-COLOR Sprayplast Verdünner 375ml
---
CELEROL-Ausbesserungsspray 918-S1 7802 lichtgrau / light grey
---
DRY MOLY Spray
UFI: MX00-F08U-COOT-P4DW
MOLYKOTE® CU-7439 PLUS SPRAY V1
---
MOLYKOTE® CU-7439 PLUS SPRAY V1
---
MOTIP SprayPlast different colours 400ml
---
Tectyl™ MULTIPURPOSE TRANSPARENT
UFI: W7KC-9CN7-300C-EJXK
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Keep respiratory protective device available.
Keep container tightly sealed.
Keep ignition sources away - Do not smoke.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
In case of contact with spray dust protective gloves made of butyl shoud be used (min. 0.4 mm thick), e.g. KCL Camatril, article no. 898 or similar products. Protective gloves. Material of gloves: Butyl rubber, BR. The selection of the suitable gloves does not only depend on the material, but also on further marks of quality and varies from manufacturer to manufacturer. Penetration time of glove material: Butyl rubber gloves with a thickness of 0.4 mm are resistant to: Acetone: 480 min, Butyl acetate: 60 min, Ethyl acetate: 170 min, Xylene: 42 min. Butyl rubber gloves with a thickness of 0.4 mm are solvent resistant for 42-480 minutes. As protective measure, we recommend that users and responsible persons for work safety assume solvent resistance length of 42 minutes. Considering the data in section 3 of this SDS, one can assume longer resistance length in particular cases. For the permanent contact in work areas without heightened risk of injury (e.g. Laboratory) gloves made of the following material are suitable: Natural rubber, NR
Tightly sealed goggles
Filter AX, Filter A2/P3. In case of brief exposure or low pollution use respiratory filter device. In case of intensive or longer exposure use self-contained respiratory protective device.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
No decomposition if used according to specifications.
No further relevant information available.
No dangerous reactions known.
No further relevant information available.
No further relevant information available.
No dangerous decomposition products known.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
12.1 Toxicity
12.1 Toxicity
12.1 Toxicity
12.2 Persistence and degradability
12.3 Bioaccumulative potential
12.4 Mobility in soil
12.5 Results of PBT and vPvB assessment
The substance is not classified as PBT or vPvB.
12.6 Other adverse effects
No further relevant information available.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
Must not be disposed together with household garbage. Do not allow product to reach sewage system.
Must not be disposed together with household garbage.
Waste Codes
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- 1950
- Shipping Name
- AEROSOLS
- Transport Class
- 2.1
- Packing Group
- not regulated
Warning: Gases.
Warning: Gases.
Warning: Gases.
Regulatory Information
Chemical regulations, safety assessments, and compliance status
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for CMP Strukturspray transparent?
The signal word is danger.
What is the physical form of CMP Strukturspray transparent?
CMP Strukturspray transparent is a aerosol with according to product specification color. It has characteristic odor.
What is CMP Strukturspray transparent used for?
Lacquer
What are the hazard statements for CMP Strukturspray transparent?
This substance has 5 hazard statements:
- H222: Extremely flammable aerosol. Pressurised container: May burst if heated.
- H315: Causes skin irritation.
- H319: Causes serious eye irritation.
- H336: May cause drowsiness or dizziness.
- H373: May cause damage to organs through prolonged or repeated exposure.
What is the melting point of CMP Strukturspray transparent?
The melting point is Undetermined. and the boiling point is Not applicable, as aerosol..