Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- Tectyl™ MULTIPURPOSE TRANSPARENT
- Product Code
- TE25030
Regulatory Identifiers
- CAS Number
- N/A
- REACH No.
- not relevant (mixture)
- UFI Code
- W7KC-9CN7-300C-EJXK
Identified Uses
Coating
Manufacturers & Suppliers
CorPro GmbH
manufacturer
Frankfurter Straße 63 - 69 65760 Eschborn Germany
00496173 9373-0
http://www.corpro.gmbh
Emergency Contacts
Emergency Contact
+32 3575 5555
24 hours emergency information
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS02
GHS07
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Dimethyl ether EC: 204-065-8 | 115-10-6 | 25 - 50% | Yes |
| Propane EC: 200-827-9 | 74-98-6 | 10 - 25% | Yes |
| Hydrocarbons, C9-C11, n-alkanes, isoalkanes, cyclics, <2% aromatics EC: 919-857-5 | 64742-48-9 | 10 - 25% | Yes |
| Hydrocarbons, C7-C9, n-alkanes, isoalkanes, cyclics EC: 920-750-0 | 64742-49-0 | 10 - 25% | Yes |
| 4-hydroxy-4-methyl-pentan-2-one EC: 204-626-7 | 123-42-2 | 1 - 5% | Yes |
| 2-methoxy-1-methylethyl acetate EC: 203-603-9 | 108-65-6 | 1 - 5% | Yes |
| OLEYL N-METHYLGLY-CINE EC: 203-749-3 | 110-25-8 | 1% | Yes |
| ALCOHOLS, C11-14-ISO-, C13-RICH, ETH-OXYLATED | 78330-21-9 | 1% | Yes |
First Aid Measures
Emergency procedures for chemical exposure incidents
If breathing is irregular or stopped, immediately seek medical assistance and start first aid actions. Provide fresh air.
Wash with plenty of soap and water. If skin irritation or rash occurs: Get medical advice/attention.
Remove contact lenses, if present and easy to do. Continue rinsing. Irrigate copiously with clean, fresh water for at least 10 minutes, holding the eyelids apart. If eye irritation persists: Get medical advice/attention.
Rinse mouth with water (only if the person is conscious). Do NOT induce vomiting. If symptoms persist: Get medical advice/attention.
Immediate Medical Attention
In all cases of doubt, or when symptoms persist, seek medical advice.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Water spray, BC-powder
Water jet
Hazardous combustion products: Carbon monoxide (CO), Carbon dioxide (CO2), Hydrocarbons, Corrosives
Co-ordinate firefighting measures to the fire surroundings. Fight fire with normal precautions from a reasonable distance.
Firefighter Protection
Wear self-contained breathing apparatus
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Remove persons to safety. Provision of sufficient ventilation. Eliminate all ignition sources if safe to do so.
Keep away from drains, surface and ground water. Retain contaminated washing water and dispose of it.
Place in appropriate containers for disposal.
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Use local and general ventilation. Use only in well-ventilated areas. Handle and open container with care. Prevent from heating up above 50 °C/122 °F.
Keep container tightly closed and in a well-ventilated place. Protect from sunlight.
Wash hands after use. Do not eat, drink and smoke in work areas. Remove contaminated clothing and protective equipment before entering eating areas. Never keep food or drink in the vicinity of chemicals. Never place chemicals in containers that are normally used for food or drink. Keep away from food, drink and animal feedingstuffs.
Prevent from heating up above 50 °C/122 °F.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
General ventilation.
Wear protective gloves. Type of material: NBR: acrylonitrile-butadiene rubber
Wear eye/face protection.
During spraying wear suitable respiratory equipment. Adequate particulate filter (EN 143).
Take recovery periods for skin regeneration. Preventive skin protection (barrier creams/ointments) is recommended.
Use appropriate container to avoid environmental contamination. Keep away from drains, surface and ground water.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
See below "Conditions to avoid".
The mixture contains reactive substance(s). Risk of ignition.
Vapours may form explosive mixtures with air.
Humidity. Air. Do not spray on an open flame or other ignition source. Keep away from heat. Protect from sunlight.
Acids, Oxidisers, Alkalis, Aluminium compound, Aluminium, Lithium compound, Oxygen, Peroxides, Lead
Reasonably anticipated hazardous decomposition products produced as a result of use, storage, spill and heating are not known. Hazardous combustion products: see section 5.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- 1950
- Shipping Name
- AEROSOLS
- Transport Class
- 2.1
- Packing Group
- not assigned
Provisions for dangerous goods (ADR) should be complied within the premises.
Provisions for dangerous goods (ADR) should be complied within the premises.
Provisions for dangerous goods (ADR) should be complied within the premises.
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for Tectyl™ MULTIPURPOSE TRANSPARENT?
The signal word is danger.
What is the physical form of Tectyl™ MULTIPURPOSE TRANSPARENT?
Tectyl™ MULTIPURPOSE TRANSPARENT is a liquid, gaseous (spray aerosol) with transparent color. It has like solvents odor.
What is Tectyl™ MULTIPURPOSE TRANSPARENT used for?
Coating
What are the hazard statements for Tectyl™ MULTIPURPOSE TRANSPARENT?
This substance has 5 hazard statements:
- H222: Extremely flammable aerosol.
- H229: Pressurised container: May burst if heated.
- H319: Causes serious eye irritation.
- H336: May cause drowsiness or dizziness.
- H412: Harmful to aquatic life with long lasting effects.
What is the melting point of Tectyl™ MULTIPURPOSE TRANSPARENT?
The melting point is not determined and the boiling point is not determined.