Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- Sikafloor®-2510 W Part B
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Epoxy coating
Manufacturers & Suppliers
Sika Schweiz AG
manufacturer
Tüffenwies 16, 8048 Zürich
+41 58 436 40 40
Emergency Contacts
Tox Info Suisse
+41(0)44 251 51 51
Tox Info Suisse
145
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS07
GHS09
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| bis-[4-(2,3-epoxipropoxi)phenyl]propane EC: 216-823-5 | 1675-54-3 | 40 - 60% | Yes |
| Reaction mass of isomers of epoxy resin BFDGE EC: 701-263-0 | --- | 10 - 20% | Yes |
| Cashew, nutshell liq., oligomeric reaction products with 1-chloro-2,3-epoxypropane EC: 500-210-7 | 68413-24-1 | 2.5 - 5% | Yes |
First Aid Measures
Emergency procedures for chemical exposure incidents
Move to fresh air. Consult a physician after significant exposure.
Take off contaminated clothing and shoes immediately. Wash off with soap and plenty of water. If symptoms persist, call a physician.
Symptoms: Allergic reactions, Erythema, Dermatitis, Causes skin irritation, May cause an allergic skin reaction.
Immediately flush eye(s) with plenty of water. Remove contact lenses. Keep eye wide open while rinsing. If eye irritation persists, consult a specialist.
Symptoms: Excessive lachrymation, Causes serious eye irritation.
Do not induce vomiting without medical advice. Rinse mouth with water. Do not give milk or alcoholic beverages. Never give anything by mouth to an unconscious person.
Immediate Medical Attention
Consult a physician.
Medical Treatment
Treat symptomatically.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
In case of fire, use water/water spray/water jet/carbon dioxide/sand/foam/alcohol resistant foam/chemical powder for extinction.
Do not allow run-off from fire fighting to enter drains or water courses.
Firefighter Protection
In the event of fire, wear self-contained breathing apparatus.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Deny access to unprotected persons.
Do not flush into surface water or sanitary sewer system. If the product contaminates rivers and lakes or drains inform respective authorities.
Soak up with inert absorbent material (e.g. sand, silica gel, acid binder, universal binder, sawdust).
Materials: sand, silica gel, acid binder, universal binder, sawdust
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Avoid exceeding the given occupational exposure limits (see section 8). Do not get in eyes, on skin, or on clothing. For personal protection see section 8. Persons with a history of skin sensitisation problems or asthma, allergies, chronic or recurrent respiratory disease should not be employed in any process in which this mixture is being used. Smoking, eating and drinking should be prohibited in the application area. Follow standard hygiene measures when handling chemical products
Keep container tightly closed in a dry and well-ventilated place. Containers which are opened must be carefully resealed and kept upright to prevent leakage. Store in accordance with local regulations.
Handle in accordance with good industrial hygiene and safety practice. When using do not eat or drink. When using do not smoke. Wash hands before breaks and at the end of workday.
Normal measures for preventive fire protection.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Maintain air concentrations below occupational exposure standards. Ensure adequate ventilation, especially in confined areas.
Chemical-resistant, impervious gloves complying with an approved standard must be worn at all times when handling chemical products. Reference number EN 374. Follow manufacturer specifications. Suitable for short time use or protection against splashes: Butyl rubber/nitrile rubber gloves (> 0,1 mm) Contaminated gloves should be removed. Suitable for permanent exposure: Viton gloves (0.4 mm), breakthrough time >30 min.
Safety glasses with side-shields conforming to EN166 Eye wash bottle with pure water
No special measures required.
Protective clothing (e.g. Safety shoes acc. to EN ISO 20345, long-sleeved working clothing, long trousers). Rubber aprons and protective boots are additionally recommended for mixing and stirring work.
Do not flush into surface water or sanitary sewer system. If the product contaminates rivers and lakes or drains inform respective authorities.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
The product is chemically stable.
No dangerous reaction known under conditions of normal use.
Stable under recommended storage conditions.
No data available
No data available
No hazardous decomposition products are known.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The generation of waste should be avoided or minimized wherever possible.
Dispose of surplus and non-recyclable products via a licensed waste disposal contractor.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- 3082
- Shipping Name
- ENVIRONMENTALLY HAZARDOUS SUBSTANCE, LIQUID, N.O.S. (epoxy resin)
- Transport Class
- 9
- Packing Group
- III
Transport in accordance with 2.10.2.7 of the IMDG-Code
Regulatory Information
Chemical regulations, safety assessments, and compliance status
All substances contained in our Products are registered by our upstream suppliers, and/or registered by us, and/or excluded from the regulation, and/or exempted from the registration.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for Sikafloor®-2510 W Part B?
The signal word is warning.
What is the physical form of Sikafloor®-2510 W Part B?
Sikafloor®-2510 W Part B is a liquid with white color. It has very faint odor.
What is Sikafloor®-2510 W Part B used for?
Epoxy coating
What are the hazard statements for Sikafloor®-2510 W Part B?
This substance has 4 hazard statements:
- H315: Causes skin irritation.
- H317: May cause an allergic skin reaction.
- H319: Causes serious eye irritation.
- H411: Toxic to aquatic life with long lasting effects.
What is the melting point of Sikafloor®-2510 W Part B?
The melting point is No data available and the boiling point is No data available.