NextSDS Logo
Safety Data Sheet EN

Lysol Disinfecting Wipes

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report.

Get Free Audit
01

Identification

Product identifiers, regulatory numbers, and supplier information

Product Information

Product Name
Lysol Disinfecting Wipes
Product Code
D8298990 (NA)

Regulatory Identifiers

CAS Number
N/A

Identified Uses

Surface Disinfectant. Consumer use

Manufacturers & Suppliers

Reckitt Benckiser LLC. logo

Reckitt Benckiser LLC.

distributor

Morris Corporate Center IV, 399 Interpace Parkway (P.O. Box 225), Parsippany, New Jersey 07054-0225

+1 973 404 2600

http://www.rbnainfo.com

R

Reckitt Benckiser (Canada) Inc.

distributor

1680 Tech Avenue, Unit #2, Mississauga, Ontario L4W 5S9, CANADA

+1 905 283 7000

Emergency Contacts

Medical

1-800-338-6167

CHEMTREC

1-800-424-9300

Chemtrec

703-527-3887

02

Hazard Identification

GHS classification, signal word, pictograms, and hazard statements

Classified no signal word

Hazard Classifications

Not Classified

GHS Pictograms

Hazard Statements

No known significant effects or critical hazards.

Precautionary Statements

Read label before use.
Keep out of reach of children.
If medical advice is needed, have product container or label at hand.

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report

Free Audit
03

Composition / Information on Ingredients

Chemical components, concentration ranges, and hazardous substance identification

Type mixture
Chemical Name CAS Number Concentration Hazardous
ethanol 64-17-5 1 - 5% Yes
D-Glucopyranose, oligomeric, C9-11-alkyl glycosides 132778-08-6 1 - 5% Yes
quaternary ammonium compounds, benzyl-C12-16-alkyldimethyl, chlorides 68424-85-1 0.1 - 1% Yes

There are no additional ingredients present which, within the current knowledge of the supplier and in the concentrations applicable, are classified as hazardous to health or the environment and hence require reporting in this section.

Notes

Any concentration shown as a range is to protect confidentiality or is due to batch variation. There are no additional ingredients present which, within the current knowledge of the supplier and in the concentrations applicable, are classified as hazardous to health or the environment and hence require reporting in this section.

04

First Aid Measures

Emergency procedures for chemical exposure incidents

Inhalation

Remove victim to fresh air and keep at rest in a position comfortable for breathing. Get medical attention if symptoms occur.

Symptoms: No known significant effects or critical hazards.

Skin contact

Flush contaminated skin with plenty of water. Remove contaminated clothing and shoes. Get medical attention if symptoms occur.

Symptoms: No known significant effects or critical hazards.

Eye contact

Immediately flush eyes with plenty of water, occasionally lifting the upper and lower eyelids. Check for and remove any contact lenses. Get medical attention if irritation occurs.

Symptoms: No known significant effects or critical hazards.

Ingestion

Wash out mouth with water. Remove victim to fresh air and keep at rest in a position comfortable for breathing. If material has been swallowed and the exposed person is conscious, give small quantities of water to drink. Do not induce vomiting unless directed to do so by medical personnel. Get medical attention if symptoms occur.

Symptoms: No known significant effects or critical hazards.

Immediate Medical Attention

Contact poison treatment specialist immediately if large quantities have been ingested or inhaled.

Medical Treatment

Treat symptomatically.

05

Firefighting Measures

Extinguishing media, specific hazards, and firefighter protection

Suitable media

Use an extinguishing agent suitable for the surrounding fire.

Unsuitable media

None known.

Instructions

Promptly isolate the scene by removing all persons from the vicinity of the incident if there is a fire. No action shall be taken involving any personal risk or without suitable training.

Firefighter Protection

Fire-fighters should wear appropriate protective equipment and self-contained breathing apparatus (SCBA) with a full face-piece operated in positive pressure mode.

06

Accidental Release Measures

Spill cleanup procedures, containment, and environmental protection

Emergency procedures

Evacuate surrounding areas. Keep unnecessary and unprotected personnel from entering. Do not touch or walk through spilled material. Put on appropriate personal protective equipment.

Small spill

Move containers from spill area. Vacuum or sweep up material and place in a designated, labeled waste container. Dispose of via a licensed waste disposal contractor.

Large spill

Move containers from spill area. Prevent entry into sewers, water courses, basements or confined areas. Vacuum or sweep up material and place in a designated, labeled waste container. Dispose of via a licensed waste disposal contractor.

Environmental

Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers.

Cleanup methods

Vacuum or sweep up material

Related Products

Similar products with comparable safety profiles

07

Handling and Storage

Safe handling precautions, storage conditions, and workplace requirements

Handling

Put on appropriate personal protective equipment (see Section 8).

Storage

Store in accordance with local regulations. Store in original container protected from direct sunlight in a dry, cool and well-ventilated area, away from incompatible materials (see Section 10) and food and drink. Keep container tightly closed and sealed until ready for use. Containers that have been opened must be carefully resealed and kept upright to prevent leakage. Do not store in unlabeled containers. Use appropriate containment to avoid environmental contamination.

08

Exposure Controls / PPE

Occupational exposure limits, engineering controls, and protective equipment

Engineering

Good general ventilation should be sufficient to control worker exposure to airborne contaminants.

Hands

Chemical-resistant, impervious gloves complying with an approved standard should be worn at all times when handling chemical products if a risk assessment indicates this is necessary.

Eyes

Safety eyewear complying with an approved standard should be used when a risk assessment indicates this is necessary to avoid exposure to liquid splashes, mists, gases or dusts. If contact is possible, the following protection should be worn, unless the assessment indicates a higher degree of protection: safety glasses with side-shields.

Respiratory

Based on the hazard and potential for exposure, select a respirator that meets the appropriate standard or certification. Respirators must be used according to a respiratory protection program to ensure proper fitting, training, and other important aspects of use.

Skin/Body

Personal protective equipment for the body should be selected based on the task being performed and the risks involved and should be approved by a specialist before handling this product. Appropriate footwear and any additional skin protection measures should be selected based on the task being performed and the risks involved and should be approved by a specialist before handling this product.

Environmental

Emissions from ventilation or work process equipment should be checked to ensure they comply with the requirements of environmental protection legislation. In some cases, fume scrubbers, filters or engineering modifications to the process equipment will be necessary to reduce emissions to acceptable levels.

09

Physical and Chemical Properties

Appearance, physical state, melting point, boiling point, and material characteristics

Relative Evaporation Rate
---
Relative Density
0.985
Flammability
Not available.
Vapor Pressure
Not available.
Solubility
Not available.
Auto Ignition Temperature
Not available.
Cloud Point
---
Ph
10.5 [Conc. (% w/w): 100%]
Melting Point
Not available.
Evaporation Rate
Not available.
Kinematic Viscosity
Not available.
Odor Threshold
Not available.
Metal Corrosion
---
Properties Status
---
Crystallisation Point
---
Colour
White.
Form
---
Solidification Point
---
Molecular Weight
---
State Under Standard Conditions
---
Boiling Point
Not available.
Upper Explosive Limit
Not available.
Bulk Density
---
Physical State
Solid. [Presaturated Wipes]
Partition Coefficient
Not available.
Voc Content
---
Physical State Data
solid
Appearance
---
Vapor Density
Not available.
Softening Point
---
Solubility In Water
---
Colour Intensity
---
Explosive Limits
---
Odor
Characteristic.
Dynamic Viscosity
Not available.
Solubility In Fat
---
Freezing Point
---
Lower Explosive Limit
Not available.
Decomposition Temperature
Not available.
Density
---
Flash Point
>93.3°C (>199.9°F)
10

Stability and Reactivity

Chemical stability, hazardous reactions, and incompatible materials

Stability

The product is stable.

Reactivity

No specific test data related to reactivity available for this product or its ingredients.

Hazardous reactions

Under normal conditions of storage and use, hazardous reactions will not occur.

Avoid

No specific data.

Incompatible

No specific data.

Decomposition

Under normal conditions of storage and use, hazardous decomposition products should not be produced.

12

Ecological Information

Environmental toxicity, biodegradation, and bioaccumulation data

The data for this section has not been processed yet.

13

Disposal Considerations

Waste treatment methods, disposal recommendations, and waste codes

Treatment

The generation of waste should be avoided or minimized wherever possible.

Disposal

Dispose of surplus and non-recyclable products via a licensed waste disposal contractor.

14

Transport Information

UN numbers, shipping names, transport classes, and regulatory requirements

UN Number
Not regulated.
15

Regulatory Information

Chemical regulations, safety assessments, and compliance status

Conforms to USDOL OSHA 29CFR 1910.1200 HAZCOM

Chemical Safety Assessment Not performed
?

Frequently Asked Questions

Common questions about safety, handling, and properties

What is the hazard signal word for Lysol Disinfecting Wipes?

The signal word is no signal word.

What is the physical form of Lysol Disinfecting Wipes?

Lysol Disinfecting Wipes is a solid. [presaturated wipes] with white. color. It has characteristic. odor.

What is the solubility of Lysol Disinfecting Wipes?

Not available.

What is Lysol Disinfecting Wipes used for?

Surface Disinfectant. Consumer use

What are the hazard statements for Lysol Disinfecting Wipes?

This substance has 1 hazard statement:

  • No known significant effects or critical hazards.

What is the melting point of Lysol Disinfecting Wipes?

The melting point is Not available. and the boiling point is Not available..