Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- 90ABC
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Extinguishing agents.
Manufacturers & Suppliers
Ansul NV/SA
distributor
Industrialaan 35 1702 Groot-Bijgaarden
+32.3.467.72.11
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
Manage your Safety Data Sheets
Organize and access chemical safety data with ease
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| MAP EC: 231-764-5 | 7722-76-1 | 87 - 93% | No |
| MAS EC: 231-984-1 | 7783-20-2 | 3% | No |
| Talc (Mg3H2(SiO3)4) EC: 238-877-9 | 14807-96-6 | 3% | No |
| Mica | 12001-26-2 | 4% | No |
| Silicon dioxide (Silica, white powder) EC: 231-545-4 | 7631-86-9 | 3% | No |
| Hexamethyldisiloxane EC: 203-492-7 | 107-46-0 | 1% | Yes |
First Aid Measures
Emergency procedures for chemical exposure incidents
Remove from exposure. If irritation persists seek medical attention.
Wash affected area with soap water. If irritation persists seek medical attention.
Wash with water for a minimum of 15 minutes. If irritation persists seek medical attention.
If patient is conscious, give large amounts of water and induce vomiting. Seek medical help.
Immediate Medical Attention
If skin irritation or rash occurs, get medical advice/attention.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
This preparation is an extinguishing media.
There are No extinguishing media which must not be used for safety reasons.
Firefighter Protection
Fire-fighters should wear appropriate protective equipment and self-contained Breathing apparatus (SCBA) with a full face-piece operated in positive pressure mode.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Prevent skin and eye contact. Evacuate personnel to safe areas. Refer to section 8 of SDS for personal protection details.
Do not allow material to be released to the environment without proper governmental permits.
Sweep up and recover for use or place in closed container for disposal
Related Substances
Similar chemicals with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Care should be taken in handling all chemical substances and preparations. See incompatibility information in section 10.
No special conditions are needed for safe storage. See incompatibility information in section 10. Store in original container or fire extinguisher. Keep tightly closed until used. There is minimal danger to the environment from a storage release.
Do not eat, drink and smoke in work areas. Wash hands after use. Remove contaminated clothing and protective equipment before entering eating areas.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Use process enclosures, local exhaust ventilation or other engineering controls to keep worker exposure to airborne contaminants below any recommended or statutory limits.
None normally needed. Use chemical resistant gloves when handling the preparation.
Use safety glasses with side shields or safety goggles.
Dust mask where dustiness is prevalent, or TLV is exceeded. Use mechanical filter respirator If exposure is prolonged.
No special equipment is needed.
Avoid discharge into the environment. According to local regulations, Federal and official regulations.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Stable at room temperature in closed containers under normal storage and Handling conditions.
The substance is stable under normal storage and handling conditions.
No dangerous reactions known.
Incompatible materials. Moist storage conditions may lead to the formation of lumps, affect product quality.
Strong alkalis, magnesium, oxidizers.
Ammonia and/or phosphorous oxides can be evolved at very high temperatures.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The material should be disposed of by incineration in a chemical in compliance with national and regional requirements.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- Not regulated
- Shipping Name
- Not regulated
- Transport Class
- Not regulated
- Packing Group
- Not regulated
Regulatory Information
Chemical regulations, safety assessments, and compliance status
Safety, health and environmental regulations/legislation specific for the substance or mixture
Other EU regulations: Employment restrictions concerning young person must be observed. use only by technically qualified individuals.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for 90ABC?
The signal word is no signal word.
What is the physical form of 90ABC?
90ABC is a powder appearing as powder with saffron yellow color. It has odorless odor.
What is 90ABC used for?
Extinguishing agents.
What is the melting point of 90ABC?
The melting point is 197℃(CAS#7722-76-1) and the boiling point is Not available.