Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- BTC-50 NF
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Coolant/Cutting solution, intended for professional use only!
Manufacturers & Suppliers
Alexander BINZEL Schweißtechnik GmbH & Co.KG
manufacturer
Postfach 10 01 53 / D-35331 Giessen
+49 (0) 6408 / 59-0
Emergency Contacts
Giftinformationszentrum der Länder Rheinland-Pfalz und Hessen, Universitätsmedizin der Johannes Gutenberg-Universität Mainz
+49 (0)6131 / 19 24 0
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS08
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
Mixture: consisting of the following components.
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| ethanediol EC: 203-473-3 | 107-21-1 | 50 - 100% | Yes |
For the wording of the listed hazard phrases refer to section 16.
First Aid Measures
Emergency procedures for chemical exposure incidents
In case of unconsciousness place patient stably in side position for transportation. Supply fresh air; consult doctor in case of complaints.
Seek medical treatment. Immediately wash with water and soap and rinse thoroughly. Seek medical treatment in case of complaints.
Rinse opened eye for several minutes under running water. If symptoms persist, consult a doctor. Protect unharmed eye.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
The data for this section has not been processed yet.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
The data for this section has not been processed yet.
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
The data for this section has not been processed yet.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Protective gloves. Check protective gloves prior to each use for their proper condition. Only use chemical-protective gloves with CE-labelling of category III. The glove material has to be impermeable and resistant to the product/ the substance/ the preparation. Selection of the glove material on consideration of the penetration times, rates of diffusion and the degradation. After use of gloves apply skin-cleaning agents and skin cosmetics. Recommended materials: Butyl rubber, BR. Recommended thickness of the material: 0.5 mm. Penetration time (min.): < 480. The selection of the suitable gloves does not only depend on the material, but also on further marks of quality and varies from manufacturer to manufacturer. The determined penetration times according to EN 374 part III are not performed under practical conditions. Therefore a maximum wearing time, which corresponds to 50% of the penetration time, is recommended. As protection from splashes gloves made of the following materials are suitable: Nitrile rubber, NBR. Recommended thickness of the material: 0.1 mm. Penetration time (min.): < 10.
Tightly sealed goggles. Protective goggles and facial protection - Classification according to EN 166.
When used properly and under normal conditions, breathing protection is not required. Use suitable respiratory protective device in case of insufficient ventilation. Filter A/P2. Respiratory protection - Gas filters and combination filters according to (DIN EN 141).
protective clothing (EN 13034)
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
The data for this section has not been processed yet.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for BTC-50 NF?
The signal word is warning.
What is the physical form of BTC-50 NF?
BTC-50 NF is a fluid with according to product specification color. It has characteristic odor.
What is BTC-50 NF used for?
Coolant/Cutting solution, intended for professional use only!
What are the hazard statements for BTC-50 NF?
This substance has 1 hazard statement:
- H373: May cause damage to the kidneys through prolonged or repeated exposure. Route of exposure: Oral.
What is the melting point of BTC-50 NF?
The melting point is Undetermined. and the boiling point is Undetermined..