Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- BTC-20 NF
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
intended for professional use only! Coolant/ Cutting solution
Manufacturers & Suppliers
Alexander BINZEL Schweisstechnik GmbH & Co.KG
manufacturer
Postfach 10 01 53 / D-35331 Giessen
+49 (0) 6408 / 59-0
Binzel Pty. Ltd.
distributor
42 Hinkler Rd, Mordialloc, Victoria, 3195, Australia
+61 (0) 39580 6500
Emergency Contacts
Poison Information Centre
131 126
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
Manage your Safety Data Sheets
Organize and access chemical safety data with ease
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
Mixture: consisting of the following components.
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| ethanediol | 107-21-1 | 25 - 50% | Yes |
For the wording of the listed hazard phrases refer to section 16.
First Aid Measures
Emergency procedures for chemical exposure incidents
In case of unconsciousness place patient stably in side position for transportation. Supply fresh air; consult doctor in case of complaints.
Immediately wash with water and soap and rinse thoroughly. Seek medical treatment in case of complaints.
Rinse opened eye for several minutes under running water. If symptoms persist, consult a doctor. Protect unharmed eye.
Seek medical treatment. If symptoms persist consult doctor.
Medical Treatment
Seek medical treatment.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
CO2, powder or water spray. Fight larger fires with water spray or alcohol resistant foam. Use fire extinguishing methods suitable to surrounding conditions.
Water with full jet
Formation of toxic gases is possible during heating or in case of fire.
Firefighter Protection
Do not inhale explosion gases or combustion gases.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Wear protective equipment. Keep unprotected persons away. Ensure adequate ventilation. Wear protective clothing. Avoid contact with skin and eyes.
Inform respective authorities in case of seepage into water course or sewage system. Prevent from spreading (e.g. by damming-in or oil barriers). Do not allow to enter sewers/ surface or ground water.
Absorb with liquid-binding material
Materials: sand, diatomite, acid binders, universal binders, sawdust
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Store in cool, dry place in tightly closed receptacles. Ensure good ventilation/exhaustion at the workplace. Prevent formation of aerosols.
Store in cool, dry place in tightly closed receptacles. Store only in the original receptacle. Store away from foodstuffs. Store in dry conditions. Keep container tightly sealed. Recommended storage temperature: 5-30 °C
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
No further data; see item 7.
Protective gloves. Check protective gloves prior to each use for their proper condition. Only use chemical-protective gloves with CE-labelling of category III. The glove material has to be impermeable and resistant to the product/ the substance/ the preparation. Selection of the glove material on consideration of the penetration times, rates of diffusion and the degradation. After use of gloves apply skin-cleaning agents and skin cosmetics. Material: Nitrile rubber, NBR. Recommended thickness: ≥ 0.1 mm. Penetration time: < 10 min. Maximum wearing time: 50% of penetration time.
Tightly sealed goggles. Protective goggles and facial protection - Classification according to EN 166.
When used properly and under normal conditions, breathing protection is not required. Use suitable respiratory protective device in case of insufficient ventilation. Filter A/P2. Respiratory protection - Gas filters and combination filters according to (DIN EN 141).
Protective clothing (EN 13034).
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
No further relevant information available.
No dangerous reactions known.
No further relevant information available.
No further relevant information available.
No dangerous decomposition products known.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
Must not be disposed together with household garbage. Do not allow product to reach sewage system. Disposal according to official regulations
Must not be disposed together with household garbage. Do not allow product to reach sewage system. Disposal according to official regulations
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- Void
- Shipping Name
- Void
- Transport Class
- Void
- Packing Group
- Void
Not applicable.
Not applicable.
Not applicable.
Regulatory Information
Chemical regulations, safety assessments, and compliance status
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for BTC-20 NF?
The signal word is no signal word.
What is the physical form of BTC-20 NF?
BTC-20 NF is a fluid appearing as fluid colourless with colourless color. It has characteristic odor.
What is BTC-20 NF used for?
intended for professional use only! Coolant/ Cutting solution
What is the melting point of BTC-20 NF?
The melting point is Undetermined. and the boiling point is 100 °C.